Testing Of The Mortar Spraying Machine; Note On Disposal; Important Information On Product Liability; Guarantee Declaration - WAGNER PLAST COAT HP 30 Originalbetriebsanleitung

EN
TEST / DISPOSAL / GUARANTEE DECLARATION
TESTING OF THE MACHINE
For safety reasons, we would recommend having the device
checked by an expert as required but at least every 12 months
to ensure that it can continue to operate safely.
In the case of unused devices, the check can be postponed
until they are next started up.
All (potentially deviating) national inspection and mainte-
nance regulations must also be observed.
If you have any questions, please contact the customer service
team at Wagner.

NOTE ON DISPOSAL

In accordance with European Directive 2002/96/EC on the
disposal of waste electrical equipment and its implementa-
tion in national law, this product may not be disposed of with
the household refuse, but must rather be recycled in an envi-
ronmentally correct manner.
Your waste WAGNER device will be taken back by us or our
representatives and disposed of environmentally correctly.
Please contact one of our service points or one of our repre-
sentatives or us directly to this purpose.

IMPORTANT INFORMATION ON PRODUCT LIABILITY

According to an EU directive, the manufacturer is only liable
without limitation for faults in the product if all parts come
from the manufacturer or have been approved by the manu-
facturer and have been mounted to the device and are operat-
ed properly. If third-party accessories or spare parts are used,
the manufacturer is exonerated wholly or partly from his/her
liability if use of the third-party accessories or spare parts have
caused a defect in the product. In extreme cases, the relevant
authorities can completely prohibit using the entire device.
With original WAGNER accessories and spare parts, compli-
ance with all safety regulations is guaranteed.
UKCA Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant regulations:
Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
The Waste Electrical and Electronic Equipment Regulations
2013
Applied harmonised standards
BS EN ISO 12100:2010, BS EN 12001:2012, BS EN 60204-1:2018,
BS EN IEC 61000-3-2:2019+A1:2021,
BS EN 61000-3-3:2013+A2:2021, BS EN IEC 61000-6-1:2019,
BS EN IEC 61000-6-3:2021, BS EN 62233:2008
46
3 + 2 YEAR GUARANTEE ON THIS WAGNER CONTRACTOR
PRODUCT
(Status 03.03.2022)
WAGNER exclusively provides the commercial buyer who has
purchased the product from an authorised specialist dealer
(hereinafter referred to as the „Customer") with a guarantee
for the products listed on the Internet at https://go.wagner-
group.com/3plus2-info in addition to the statutory warranty
regulations, unless there is a guarantee exclusion.
The guarantee period for WAGNER products (devices) in the
contractor's sector is 36 months and begins with the date
of purchase of the initial purchase. This guarantee period
is extended by a further 24 months if the product is regis-
tered within 28 days of purchase on the Internet at https://
go.wagner-group.com/3plus2.
In cases of commercial rental, industrial use (e.g. use in shift
operation) or equivalent use, the guarantee period is 12
months due to the significantly higher load. We reserve the
right to carry out a check in individual cases and refuse the
guarantee where necessary.
If any material, machining or performance defects are identi-
fied in the device within the guarantee period, then the gua-
rantee claims must be made immediately and within a period
of no more than 2 weeks following discovery of the defect.
The detailed guarantee conditions can be obtained on
request from our authorised WAGNER partners (see website
or operating instructions) or in text form on our website:
https://go.wagner-group.com/pf-warranty-conditions
EU Declaration of conformity
We declare under sole responsibility that this product
conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN ISO 12100, EN 1953, EN 60204-1, EN IEC 61000-3-2,
EN 61000-3-3, EN IEC 61000-6-1, EN 61000-6-3, EN 62233
The EU declaration of conformity is enclosed with the
product.
If required, it can be re-ordered using order number
2395947.
Plast Coat HP 30
Subject to modifications