Safety Regulations; Layout And Items Supplied - EINHELL 40.104.70 Originalbetriebsanleitung

Important!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Caution!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.

2. Layout and items supplied

2.1 Layout (Fig. 1-4)
1. Intake air fi lter
2. Pressure tank
3. Wheel (axle mounted)
4. Foot
5. Quick-lock coupling (regulated compressed
air)
6. Pressure gauge (for reading the set pressure)
7. Pressure regulator
8. On/Off switch
9. Transport handle
10. Safety valve
11. Drainage screw for condensation water
12. Pressure gauge (for reading the vessel pres-
sure)
13. Quick-lock coupling (unregulated com-
Anl_TE_AC_400_50_10_SPK1.indb 18 Anl_TE_AC_400_50_10_SPK1.indb 18
GB
pressed air)
14. Oil sealing plug
15. Oil drainage screw
16. Overload switch
17. Oil fi ller opening
18. Wheel cap
19. Screw (internal hexagon) for fi tting the handle
20. 4mm Allen key
21. Screw
22. Washer (small)
23. Nut for fi tting the foot
24. Axle screw
25. Spring washer
26. Nut for fi tting the axle
27. Washer
2.2 Items supplied
Please check that the article is complete as spe-
cifi ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Important!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Intake air filter (2x)
•
Wheel (axle pre-mounted) (2x)
•
Foot (2x)
•
Transport handle
•
Oil sealing plug
•
Wheel cap (2x)
•
Screw (Allen) for fitting the handle (2x)
•
4 mm Allen key
•
Screw (2x)
•
Washer, large (4x)
•
Washer, small (4x)
•
Nut for fitting the foot (2x)
- 18 -
27.01.14 09:04 27.01.14 09:04