Intended Use; Before Use - Triton TMNRTR Bedienungsanleitung

23. Guide Rail Slot
24. Plunge Lock Lever
25. Guide Rail Locking Knob
26. Base of Plunge Base
27. Plunge Base Plate
28. Plunge Base Locking Knob
29. Depth Stop Lock
30. Depth Stop
31. Depth Turret
32. Table Height Micro Winder Connector
33. Guide Bush Locking Screw
34. Dust Extraction Spout Connection Screw
35. Plunge Base Plate Screw
36. Trimmer Base Locking Knob
37. Trimmer Depth Locking Knob
38. Trimmer Base Plate
39. Trimmer Base Plate Screw
40. Guide Bearing
41. Roller Guide Adjustment Locking Knob
42. Roller Guide Adjustment Knob
43. Roller Guide Locking Knob
44. Washer
45. Trimmer Base Guard
46. Trimmer Depth Micro Adjustment Dial
47. Roller Guide Alignment Channel
48. Router Bit (not supplied)
49. Guide Bush (not supplied)
50. Spring Washer
51. Hex Screw
52. Table Height Winder
Figures XII and XIII
a Template
b Workpiece
c Offset

Intended Use

A mains-powered mini router intended for routing profiles, edges,
grooves, holes and for copy routing in plastic, light building
materials, and wood. Predominantly for hand held use.
Note: Not intended for commercial use.
Unpacking Your Product
• Carefully unpack and inspect your product. Fully familiarise
EN
yourself with all its features and functions
• Ensure all parts of the product are present and in good
condition
• If any parts are missing or damaged, have such parts replaced
before attempting to use this product
16
817698_OwnerManual.indd 16 817698_OwnerManual.indd 16

Before Use

WARNING: Ensure the tool is disconnected from the power
supply before attaching/changing any accessories or making any
adjustments.
Collet & router bit installation
WARNING: Wear protective gloves when inserting and
removing router bits due to the sharp edges of the cutters.
WARNING: Always use cutters and bits with the correct size
shank for the chosen collet size.
Note: It is easiest to install a cutter prior to fitting the router to a
base; however, it is possible to change the Router Bit (not supplied)
(48) when attached to a base.
See Fig. I
1. Press the Spindle Lock Button (16) then rotate the Collet Nut
(17) until the spindle lock engages
2. Slacken the Collet Nut, using the supplied Spanner (2) if
required, and remove the Collet Nut
3. Ensure the correct size Collet is chosen to match the required
Router Bit (48) then place the Collet into the spindle, then
reapply the Collet Nut
4. With the correct Collet in place and Collet Nut attached but
slackened, insert the Router Bit into the Collet, ensuring that at
least half of the Router Bit's shaft is inserted
5. Tighten the Collet Nut with the Spanner, ensuring that the
Router Bit cutter has 1-2mm clearance from the Collet and is not
butted tight against the Collet or the Collet Nut; vibration from
the cutter could vibrate the Collet Nut and cause it to loosen
during use
WARNING: DO NOT over-tighten the Collet Nut! This could
cause damage to the Collet, Collet Nut, external thread and Spindle
Lock.
Note: Do not tighten the Collet Nut with no Router Bit fitted. This
can bend and damage the Collet. Keep the Collet Nut partially
screwed in until a Router Bit is fitted. Be aware of the spring in the
spindle that keeps pressure on the Collet up against the Collet Nut.
When installing the Collet, a small amount of pressure is required
when applying the Collet Nut to the spindle drive thread.
6. To remove a Router Bit, engage the Spindle Lock by pressing
the Spindle Lock Button then slacken the Collet Nut with the
Spanner
7. With the Collet Nut sufficiently slackened, the Router Bit can be
removed
WARNING: ALWAYS keep the Collet, Collet Nut, spindle drive
thread and Router Bit shank clean and free of oil and grease to
ensure a reliable and secure fitting.
Fitting to plunge base
Note: If the Router (1) is attached to the Trimmer Base (8), remove
the Trimmer Base before attempting to fit the router to the Plunge
Base (9).
1. Ensure the Plunge Base Locking Knob (28) is wound out so the
screw is not protruding into the base
2. Align the Router (1) so the Securing Hole (18) is directly above
the Plunge Base Locking Knob (Fig. II)
11/11/2022 10:25 11/11/2022 10:25