Hitachi DS 18DL2 Bedienungsanleitung Seite 16

English
Work
Brick <DV14DL2 / DV18DL2>
Wood
Drilling
Steel
Aluminum
Machine screw
Driving
Wood screw
6. How to select tightening torque and rotational speed
Use
Machine screw
Driving
Wood screw
Brick
<DV14DL2 / DV18DL2>
Drilling
Wood
Metal
CAUTION:
The selection examples shown in Table 5 should be
considered as general standard. As different types of
tightening screws and different materials to be
tightened are used in actual works proper adjustments
are naturally necessary.
When using the driver drill with a machine screw at
HIGH (high speed), a screw may damage or a bit may
loose due to the tightning torque is too strong. Use
the driver drill at LOW (low speed) when using a
machine screw.
NOTE:
The use of the battery in a cold condition (below 0
degree Centigrade) can sometimes result in the
weakened tightening torque and reduced amount of
work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
7. Using the hook
CAUTION:
When using the hook, pay sufficient attention so that
the main equipment does not fall. If the tool falls,
there is a risk of accident.
Do not attach the tip tool except phillips bit to the tool
main unit when carrying the tool main unit with the
hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side and the
angle can be adjusted in 5 steps between 0° and 80°.
15
Table 4
Use for drilling purpose.
Use the bit or socket matching the screw diameter.
Use after drilling a pilot hole.
Table 5
Rotating speed selection (Position of the shift knob)
Clutch dial Position
For 6 mm or smaller
1 – 22
diameter screws.
For 8 mm or smaller nominal
1 –
diameter screws.
For 14 mm or smaller
diameters. (DV14DL2)
For 16 mm or smaller
diameters. (DV18DL2)
For 50 mm or smaller diameters.
(DS14DL2 / DV14DL2)
For 65 mm or smaller diameters.
(DS18DL2 / DV18DL2)
Suggestions
LOW (Low speed)
(1) Operating the hook
(a) Pull out the hook toward you in the direction of
arrow (A) and turn in the direction of arrow (B).
(Fig. 10)
(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,
60°, 80°).
Adjust the angle of the hook to the desired position
for use.
(2) Switching the hook position
CAUTION:
Incomplete installation of the hook may result in
bodily injury when used.
(a) Securely hold the main unit and remove the screw
using a slotted head screwdriver or a coin. (Fig. 11)
(b) Remove the hook and spring. (Fig. 12)
(c) Install the hook and spring on the other side and
securely fasten with screw. (Fig. 13)
NOTE:
Pay attention to the spring orientation. Install the
spring with larger diameter away from you. (Fig. 13)
(3) Using the bit holder (Hook with bit holder)
Installing the bit
Slide the bit from the side, and then insert firmly
until the groove on the bit locks in the protruded
section of the hook.
Removing the bit
Securely hold the main unit and pull out the bit by
holding the tip with your thumb. (Fig. 14)
CAUTION:
Only Hitachi STANDARD ACCESSORIES phillips bit
(No. 2 × 65L; Code No. 983006) may be used. Do not
use other bits since they may come loose.
HIGH (High speed)
For 4 mm or smaller
diameter screws.
For 4.8 mm or smaller
nominal diameter screws.
For 10 mm or smaller
diameters. (DV14DL2)
For 12 mm or smaller
diameters. (DV18DL2)
For 24 mm or smaller diameters.
(DS14DL2 / DV14DL2)
For 27 mm or smaller diameters.
(DS18DL2 / DV18DL2)
For drilling with a metal
working drill bit.