Herunterladen Inhalt Inhalt Diese Seite drucken

Dolmar AM3746 Betriebsanleitung Seite 11

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 28
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
WARNING:
Always be sure that the lock key
and battery cartridge are removed before carrying
out any work on the mower. Failure to remove the
lock key and the battery cartridge may result in seri-
ous personal injury from accidental start-up.
WARNING:
Never start the mower unless it is
completely assembled. Operation of the tools in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Installing the handle
NOTICE:
When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1.
Attach the lower handle so that the holes in the
handle fit in the protrusions on the mower body. Insert
the bolts from inside, then attach washer A from outside,
and then tighten the thumb nuts.
► Fig.1: 1. Lower handle 2. Washer A 3. Thumb nut
4. Protrusion 5. Hole 6. Bolt
2.
Align the hole in the lower handle with the hole
in the upper handle, then insert the bolts from inside,
then attach washer B from outside, and then tighten the
thumb nuts.
► Fig.2: 1. Upper handle 2. Hole 3. Washer B
4. Thumb nut 5. Lower handle 6. Bolt
Hold the upper handle firmly so
CAUTION:
that it does not drop off your hand. Otherwise, the
handle may fall and cause an injury.
3.
Attach holder A and holder B to the handle.
Position the cords as shown in the figure.
► Fig.3: 1. Cord 2. Holder A 3. Holder B
NOTE: When attaching holder A, be sure to fix the
cord with the holder as shown in the figure.
Removing the mulching attachment
1.
Open the rear cover.
► Fig.4: 1. Rear cover
2.
Remove the mulching attachment while holding
down the lever.
► Fig.5: 1. Lever 2. Mulching attachment
Installing the grass basket
1.
Open the rear cover.
► Fig.6: 1. Rear cover
2.
Hook the grass basket on the rod of the mower
body as shown in the figure.
► Fig.7: 1. Rod 2. Guard 3. Grass basket
NOTICE:
Make sure that the guard on the grass
basket is facing downward. Otherwise, the grass
basket may not catch all of cut-off grass.
Attaching the mulching attachment
1.
Open the rear cover, and then remove the grass
basket.
► Fig.8: 1. Rear cover 2. Grass basket
2.
Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
► Fig.9: 1. Lever 2. Mulching attachment
11 ENGLISH

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis