Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch PWS Professional 2000-230 JE Originalbetriebsanleitung

18 | English
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
in diameter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Technical Data

Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
1 609 92A 222 | (27.11.2020)

Intended use

The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A special protective guard for cutting must be used when
cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Auxiliary handle (insulated gripping surface)
(4) Grinding spindle
(5) Protective guard for grinding
(6) Locking screw for protective guard
(7) Mounting flange with O‑ring
(8) Grinding disc
(9) Clamping nut
(10) Two-pin spanner for clamping nut
(11) Quick-clamping nut
(12) Carbide grinding head
(13) Protective guard for cutting
(14) Cutting disc
(15) Cup grinding wheel
(16) Offset two-pin spanner for cup grinding wheel
(17) Hand guard
(18) Spacer discs
(19) Rubber sanding pad
(20) Abrasive disc
(21) Round nut
(22) Cup brush
(23) Extraction guard for cutting with cutting guides
(24) Diamond cutting disc
(25) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
PWS 2000-230 JE PWS 20-230
3 603 CC6 0.. 3 603 C59 W..
W 2000
W 1250
-1
min 6500
mm 230
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
PWS 20-230 J PWS 1900
3 603 C59 V.. 3 603 C59 W..
2000 2000
1250 1250
6600 6600
230 230
Bosch Power Tools
a)
a)
1900
1170
6600
230