Operation - Makita DBN500 Betriebsanleitung

ASSEMBLY
CAUTION:
• Always make sure that your fingers are not placed on
the trigger, and the battery cartridge and nails are
removed before carrying out any work on the nailer.
Loading or unloading the nails
CAUTION:
• Always make sure that your fingers are not placed on
the trigger and the battery cartridge is removed before
loading nails.
• Do not abruptly slide the slide door of the nailer loaded
with nails. Accidentally dropping nails especially when
working in high places may cause personal injuries.
• Load nails in the correct direction. Loading in wrong
direction may cause premature wear and tear of the
driver and damage of the other parts.
• Do not use deformed connected nails. Use nails
specified in this manual. Using nails other than those
specified may cause nail jamming and breakage of the
nailer.
Press the lock lever and open the slide door of the
magazine. (Fig. 8)
Set the nail strip so that the nail tips touch the bottom of
the magazine slit and slide the nail strip toward the firing
opening.
Return the slide door to the original position until the lock
lever locks it.
To remove the nails, press the lock lever and slide the
slide door. Take out nails from the magazine slit. (Fig. 9)
Nose adapter
CAUTION:
• Always make sure that your fingers are not placed on
the trigger, and the battery cartridge and nails are
removed before installing the nose adapter. (Fig. 10)
When firing nails on the material to be fastened with
easily-marred surfaces, use the nose adapter. To install
the nose adapter, place it over the center plate so that the
protrusion inside the nose adapter fits to the slit in the
driver guide cover.
When not in use, store the nose adapter in the holder at
the back end of the slide door to keep it from being lost.
Total two nose adapters can be stored.
Hook
CAUTION:
• Always make sure that your fingers are not placed on
the trigger, and the battery cartridge and nails are
removed before using the hook.
• Do not hang the hook from the waist belt. Dropping the
nailer, which is caused by the hook accidentally coming
out of place, may cause misfiring and personal injuries.
(Fig. 11)
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw. To
remove, loosen the screw and then take it out. (Fig. 12)
8
Hex wrench storage (Fig. 13)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.

OPERATION

Inspecting trigger function
CAUTION:
• Make sure that the trigger function is in working order
before each operation. If you find issues described
below, ask Makita Authorized Service Centers for
repairs.
• Before installing the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
The tool must not operate only by pulling the trigger or
only by placing the contact element against the work
piece.
Driving nails
CAUTION:
• Always be sure to first place the contact element
against the workpiece before pulling the trigger.
Select the nailing mode by pressing the mode selecting
button as mentioned in the section "Nailing mode
selection".
Intermittent nailing (sequential mode) (Fig. 14)
To drive a nail, set the lock button to the "FREE" position.
Place the contact element against the workpiece and pull
the trigger. Release the trigger after each operation.
Continuous/intermittent nailing (continuous mode)
(Fig. 15)
When the tool is set to continuous mode, you can operate
either continuous or intermittent nailing.
To drive a nail, set the lock button to the "FREE" position.
- For continuous nailing, pull the trigger first and then
place the contact element against the workpiece. For
the next actuation, you do not need to release the
trigger.
- For intermittent nailing, place the contact element
against the workpiece and pull the trigger. For the next
actuation, you need to reset the trigger first.
NOTE:
• This tool stops automatically under the following
conditions:
- If you release the trigger or contact element from
workpiece before the tool finishes the operation
completely.
In this situation, pull the trigger again until the tool turns
into standby.
- When keep either pulling the trigger or placing the
contact element about 5 seconds without another
action.
In this case, release the trigger or the contact element
from workpiece to restart the operation.
Anti dry fire mechanism
This tool is equipped with an anti dry fire mechanism. It
automatically stops driving nails when the remaining nails
finish. In this case, load more nails to resume operation.