Bluetooth Usb Adapter; Connection Diagram - Bosch KTS 5-Serie Originalbetriebsanleitung

en 22 | KTS 530 / 540 / 570 (KTS 5 Series) | Description of unit
3.6 Bluetooth
3.6.1

Bluetooth USB adapter

The Bluetooth USB adapter, which is included with
delivery, allows wireless connection with KTS 540 / 570. It
is connected to the PC/Laptop and shows that it is ready
for operation when the red LED is illuminated.
!
It is not possible to operate another piece of bluetooth
hardware installed or plugged into the PC/laptop, as
the data communication between the KTS module and
the control unit would be disrupted as a result.
!
Do not put any mechanical stress on the Bluetooth
USB adapter and do not use it for gripping. This can
damage the laptop or Bluetooth USB adapter.
3.6.2 Toshiba Bluetooth driver
Bluetooth Manager symbol
board diagnosis function is active:
Color Function
Green Bluetooth USB adapter active and communi-
cating with KTS 540 / 570.
White Bluetooth USB adapter plugged into PC/lap-
top, but Bluetooth connection inactive.
White/green in Bluetooth USB adapter tries to create a wire-
7-sec. cycle. less connection to the KTS module.
Red Bluetooth USB adapter not plugged into PC/
laptop.
Bosch Bluetooth Device symbol
the on-board diagnosis function is active:
Color Function
Green Field strength of Bluetooth wireless link OK.
Red Field strength of Bluetooth wireless link too
low. Reduce distance between
Bluetooth USB adapter and the KTS
module or avoid obstacles such as e. g. steel
doors or concrete walls.
Symbol not No Bluetooth wireless connection.
there. Follow the instructions in chapter 4.6.
i
Interrupting the Bluetooth connection with the
KTS 540 / 570 can activate an acoustic alarm signal
in the PC/Laptop (see Online Help DDC). If a fault
occurs, the USB connection can be activated and
used instead of the Bluetooth connection.
3.6.3 Microsoft Bluetooth driver
When the Microsoft Bluetooth driver is activated, the
Bluetooth manager symbol
and the Bluetooth device symbol
Bluetooth device symbol is not displayed if there is no
Bluetooth wireless link.
|
1 689 989 289 2014-12-04
(in toolbar) when the on-
(in toolbar) when
always appears in "white"
in "green". The
3.7 Operation
KTS 530 can only be connected with the PC/Laptop via
the USB interface. KTS 540 / 570 can be linked with the
PC/Laptop via wireless connection (Bluetooth) or via
the USB interface. Insert the Bluetooth USB adapter in
the PC/Laptop for a wireless connection.
i
The radio connection between KTS 540 / 570
and the PC/Laptop can only be made with the
Bluetooth USB adapter provided in the delivery. The
DCU 130 with internal Bluetooth hardware does
not require the use of the supplied Bluetooth USB
adapter and the installation of the Bluetooth driver.
3.7.1

Connection diagram

1
9
2
10
3
11
12 4
13 5
14
6
15
7
16
8
X9
12
V
BOSCH
I
D
E
O
X2 Mouse X7 LPT1
X25 USB1
1
0 X1 K ayboard X3 COM1 X4 COM2
X26 USB2
11
10
8
Fig. 3: Connection diagram in an example for the KTS 570
1 OBD interface in vehicle
2 UNI connection cable
3 OBD diagnosis cable
4 Measurement cables (KTS 570)
5 Measurement cables (KTS 530, KTS 540)
6 GND lead
7 Power pack
8 Adapter insert (IBOX 01)
9 KTS 570
10 USB connecting cable
11 Bluetooth USB adapter
12 PC (Laptop)
!
Only use the UNI connecting cable (Fig. 3, Item 2)
for measurements with less than 30 V.
1
3
2
5
4
9
6
7
Robert Bosch GmbH