EINHELL FREELEXO LCD BT Originalbetriebsanleitung Seite 38

5.8 Securing the charging station
Once the robot lawn mower is working properly
and a suitable position for the charging station
(19) has been found, the charging station (19)
must be fi xed in place using the fastening screws
(15). Use the hexagon key (23) to secure the fas-
tening screws (15) fully in the ground (Fig. 7c).
5.9 Battery capacity indicator (Fig. 13b)
Press the button for the battery capacity indicator.
The battery capacity indicator shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Important!
When using a multi-Ah pack (e.g. 4-6Ah), always
set the higher capacity. Thanks to the gentle
charging and discharging of the robot lawn mower
there is no need to use the lower capacity in order
to extend the working life.
5.10 Charging the rechargeable battery with
the charger
In normal operation the battery (A) of the robot
lawn mower is charged via the charging station
(19). For independent use of the battery (A) from
the Power-X-Change series it can also be char-
ged in the external Power-X-Charger. Important!
– Depending on the model of your robot lawn mo-
wer, it might not come complete with the battery
charger (Fig. 13a/Item B).
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(B) into the socket outlet. The green LED will
then begin to fl ash.
2. Insert the rechargeable battery (A) into the
battery charger (B) (Fig. 13a).
Anl_FREELEXO_LCD_BT_SPK13.indb 38 Anl_FREELEXO_LCD_BT_SPK13.indb 38
GB
3. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6. Operation
6.1 Main switch
The robot lawn mower is equipped with a main
switch (7). Use the main switch (7) to switch the
robot lawn mower on (ON) and off (OFF)(Fig. 8).
Once the robot lawn mower has been switched
on, it is locked by a PIN.
6.2 Control panel
The robot lawn mower has already been pro-
grammed at the factory and default settings have
been made for it. However, these can be changed
if required. Even though the factory settings will
be suitable for most gardens, you should still
familiarize yourself with the available options ne-
vertheless.
- 38 -
16.11.2023 10:09:18 16.11.2023 10:09:18