BURG WÄCHTER TRSE 10 Bedienungsanleitung Seite 5

Structure
Figure
Clear button
Quitting the programming mode
On / Enter button
Readiness for opening
LED goes on when a valid opening code is entered and programming
is successful.
Battery replacement symbol
When this LED is on, please replace all 3 batteries
(LR6 / AA / 1.5V / Alkaline).
Readiness for entry / programming
The LED goes on when the programming mode is entered. It goes off when
the programming mode is exited again.
Rejected entry / blocking time
The LED goes on when an invalid code is entered or when the programming
is incorrect. In case a wrong code is entered three times in a row, the lock is
blocked for 5 minutes. During this time, the LED flashes. In this status, opening
is not possible, even with a correct opening code.
TRSE 10
Dear customer,
Thank you for deciding for a safe with the BURG-WÄCHTER TRSE10 electronics.
This electronics is certified according to VdS class 1 and opening is possible both
with fingerprint and using a Pincode. You have thus acquired a product meeting
extremely high security requirements and developed and manufactured using the
latest technical potential.
Important: Please read the entire User Manual before programming
and store this User Manual at a safe place for future reference at any time
you may need it.
We hope you will enjoy your BURG-WÄCHTER safe.
Your BURG-WÄCHTER KG
Important information about our electronic locks
General information:please take care that the codes and the code carrier
do not fall into the wrong hands. Therefore, store the codes and code
carrier at a safe location so that these can only be accessed by authorised
persons. In case you loose a code or code carrier, the lock must be
converted to a new code / code carrier, or replaced.
– The factory code must be changed as soon as the lock is commissioned.
– Simple codes that are easy to guess (e. g. 1, 2, 3, 4, 5, 6) must not be used.
– Personal data (e. g. birthday) or other data that may be concluded with
knowledge of the code owner must not be used as code.
– After changing the code, the lock must be checked several times with the
safety door opened.
Generally
A Pincode and 10 memory slots for fingerprints are available for opening.
Pincode: 123456 (factory setting)
The Pincode has always 6 digits.
For fingerprint opening, two different fingers need to be used, which have to be
dragged over the sensor successively.
When an action has been successfully completed, the green LED goes on.
Technical data
Number of Pincodes 1
Number of 10
fingerprints
Blocking times
When a wrong code is entered 3 times, 5 minutes,
subsequently 10 minutes after each wrong entry
Power supply
3 x MIGNON LR6 / AA / ALKALINE
Permissible ambient - 15 °C through +50 °C
conditions
Up to 95 % rel. air humidity (non condensing)
Menu structure
The individual labels on the keypad indicate numerals and letters. Combinations
of numerals and / or letters are used to program the individual functions. The initial
letters of a programming procedure are composed as a combination of numbers
(to facilitate their remembering). When using these explicit combinations,
the individual submenus are opened.
Opening with Pincode
– Press „On / Enter", the yellow LED of the Readiness for entry / programming
icon goes on.
– Enter the Pincode. The green LED goes on when entered correctly, the red one
when the entry is rejected.
Turn the rotary handle clockwise to open the door.
Opening with finger
– Press „On / Enter", the yellow LED of the Readiness for entry / programming
icon goes on.
– Move your 1st finger over the sensor.
The yellow LED goes off, the green LED goes briefly on when the finger is
accepted, then the yellow LED goes on again.
– Move your 2nd finger over the sensor.
The yellow LED goes off, the green LED goes briefly on when the finger is
accepted.
Turn the rotary handle clockwise in order to open the door.
Access to the programming mode to change
the lock settings
– Press „On / Enter", the yellow LED of the Readiness for entry/programming
icon goes on.
– Type numbers 76 (program mode), the yellow LED goes off.
– Press „On / Enter" and enter the valid Pincode.
When a valid Pincode has been entered, the green LED goes on briefly,
subsequently the yellow LED flashes. As long as the yellow „Readiness for
entry / programming" LED is flashing, you are in the programming mode and
so you can perform various actions.
bat
English | 2