Specifications; Additional Safety Rules - Makita JN3200 Betriebsanleitung

ENGLISH
1 Lock button
2 Switch trigger
3 Gauge for mild steel : 3.2 mm
4 Gauge for stainless : 2.5 mm
5 Mouth (3.5 mm clearance)
6 Wrench
7 Lock nut
8 Die holder

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Min. cutting radius
Outside edge ................................................... 128 mm
Inside edge ...................................................... 120 mm
Strokes per minute ................................................. 1,300
Overall length ..................................................... 215 mm
Net weight ............................................................. 3.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.

ADDITIONAL SAFETY RULES

1. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
2. Always lead the power supply cord away from
the tool towards the rear.
3. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
9 Punch
10 Screw
11 Loosen
12 Cutting edge
13 Groove
14 Pin
15 Punch holder
16 Grind/sharpen; 0.3 – 0.4 mm
2
........................... 3.2 mm/10 ga
2
........................... 2.5 mm/13 ga
2
........................... 1.0 mm/20 ga
2
................... 2.5 mm/13 ga
OPERATING INSTRUCTIONS
JN3200
Pre-lubrication
Coat the cutting line with tool oil when cutting mild steel
or stainless; use light oil or kerosene when cutting alumi-
num.
Switch action (Fig. 1)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
Permissible cutting thickness (Fig. 2)
The thickness of material to be cut depends upon the
tensile strength of the material itself. The groove on the
die holder acts as a thickness gauge. Do not attempt to
cut any material which will not fit into this groove.
Max.cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
This tool can cut any thickness of aluminum plate that fits
into the tool's mouth (3.5 mm clearance).
Cutting method (Fig. 3)
Smooth cutting is achieved by holding the tool upright
and applying gentle pressure in the cutting direction.
Apply tool oil to the punch about every 10 meters of mild
steel or stainless steel to be cut. Light oil or kerosene
should be used to keep an aluminum lubricated continu-
ously. Failure to lubricate aluminum in the cut will cause
chips to adhere to the tool, dulling the die and punch and
increasing load on the motor.
Cutouts (Fig. 4)
Cutouts can be done by first opening a round hole of
about 42 mm diameter or more in the material.
17 Remove dull portion
18 Die
19 Washer
20 Limit mark
21 Screwdriver
22 Brush holder cap
mm
2
3.2
2
2.5
2
1.0
2
2.5
ga
10
13
20
13