Cardin Elettronica SLX24DRACO2 Bedienungsanleitung Seite 14

Anchoring the unit SLX3024 - SLX1524 - SLX1024REV - SLX824 (fig. 9, 10)
Important! Check the exact anchoring position with respect to the alignment of the sliding gate
• Run the piping and connection wires to the position where the motor is to be
installed.
• Attach the anchor bolts to the base plate 'A' allowing them to protrude
by 50 mm and then tighten down using the supplied M12 nuts.
• Prepare a cement plinth, in the position where the motor is to
be installed, with a depth of 350 mm (the base should protrude
by about 25 mm to avoid damage by pools of water building up
under the appliance).
• Insert the base plate making sure that:
- the electrical cables pass through the hole 'B';
- the anchor bolts 'C' are immersed into the cement base and the base plate
is perfectly level;
- the four protruding threaded bolts are perpendicular to the base plate;
- the surface area of the base plate is clean and free of cement residue.
If the runner guide already exists the cement base should be extended to take in part of the
runner guide foundation. This will stop the two foundations from giving way separately.
- Unscrew the four M12 nuts on the four threaded bolts (previously used to block the anchor
bolts) from the base of the anchor plate. Then insert the four washers and allow them to rest on
the nuts.
- Position the geared motor over the four threaded bolts and allow it to rest on the four washers.
- Fasten in to the base using the other four washers and
adjustment nuts supplied with the kit, making sure that the unit remains perfectly level and stable.
- Adjust the height if the unit using the four grub screws already positioned on the motor. This will
allow you to adjust the height and position of the motor later on.
Fitting the gear rack
- release the geared motor (fig.
11-12), lay the first stretch of the
toothed rack on the pinion and fix
it to the gate, then fasten down all
the other parts along the entire
length of the gate.
- after having fastened the toothed
rack, realign the pinion (play of 1
to 2 mm between the gear runner
and the pinion) using the grub
screws at the base of the geared
motor. This action will prevent the
weight of the sliding gate from
damaging the unit when working.
MANUAL MANOEUVRE WITH THE MOTOR RELEASED
Manual release is to be carried out with the motor stopped. To release the gate use the manual
release key supplied with the unit. The key should be kept in an easily accessible place.
SCREW OPERATED MANUAL RELEASE SYSTEM SLX3024
To release the unit
1. Rotate the lock protection disk, insert the key, rotate it half a turn anticlockwise and lift up
the knob cover.
The knob is now free and can be released.
2. Rotate the knob clockwise until it can turn no more.
Attention: do not force the knob to turn further than its travel limit.
The gears are now released and the gate can be moved manually.
To relock the unit
1. Rotate the knob anticlockwise and move it back to the blocked position.
2. Close the knob cover, rotate the key clockwise and rotate the lock protection disk cover.
The gears are now blocked and the gate is ready for use.
Once the system has been reset store the key in a safe place.
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
2 mm
SCALA: 1:2
Drawing number :
DI0240
Product Code : SL1524
Date :
Draft : P.J.Heath 08-02-2002
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
All rights reserved. Unauthorised copying or use of the information contained in this document is p
SCALA: 1:2
Drawing number :
DI0237
Product Code : SL1524M
Draft : P.J.Heath Date : 30-01-2002
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
ANCHORING
THE UNIT
Plan view
ANCHORING
THE UNIT
Side view
All rights reserved. Unauthorised copying or use of the information contained in this docum
SCALA: 1:2
Drawing number : DI0532
Product Code : SL1524
P.J.Heath Date :
Draft :
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401
Description : Prodotti Technocity
VISTA DI FIANCO CON MOTORE
14
B
C
Gear rack
Description : Prodotti Technocity
Base plate
CONTROPIASTRA SL1524M
34 69
157
104,5
10
SLX3024
Description :
Vista in pianta e di fianco senza motore
23.04.2009
A
9
2
M 1
A
Gate
11