Roller Bending Spray In Spray Cans Contains Environmentally Friendly; Explanation Of Symbols; Technical Data; Scope Of Supply - Roller Arco Betriebsanleitung

eng
● Be careful when bending with ROLLER pipe bending machines. These
develop a high bending force. Danger of injury from improper use.
● Never let the power tool operate unattended. Switch off the power tool
during longer work breaks, pull out the mains plug/battery. Electrical devices
can cause hazards which lead to material damage or injury when left unattended.
● Only allow trained persons to use the power tool. Apprentices may only use
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
safely may not use this power tool without supervision or instruction by a
responsible person. Otherwise there is a risk of operating errors and injuries.
● Check the power cable of the power tool and extension leads regularly for
damage. Have these renewed by qualifi ed experts or an authorised ROLLER
customer service workshop in case of damage.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
● ROLLER bending spray in spray cans contains environmentally friendly
but highly infl ammable propellant gas (butane). Aerosol cans are pres-
surised; do not open by force. Protect them against direct sunlight and
temperatures above 50°C. The aerosol cans can burst, risk of injury.
Safety notes for batteries, rapid chargers,
power supply units
WARNING WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to heed the instructions can result in electric shock,
fi re and/or severe injuries.
Save all warnings and instructions for future reference.
See also www.albert-roller.de → Downloads → Operating Instructions and
www.albert-roller.de → Downloads → Safety Data Sheets → Batteries.

Explanation of symbols

WARNING WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use ear protection
Power tool complies with protection class II
Not suitable for using outdoors
Environmentally friendly disposal
CE conformity mark

1. Technical Data

Use for the intended purpose
WARNING WARNING
ROLLER'S Arco and ROLLER'S Arco 22 V are intended for the purpose of cold draw Arco 22 V Arco 22 V are intended for the purpose of cold draw
bending of pipes up to 180°.
ROLLER'S Arco 50 is intended for cold draw bending of pipes up to 90°.
All other uses are not for the intended purpose and are prohibited.

1.1. Scope of Supply

ROLLER'S Arco: Electric pipe bending machine, insert bolts,
bending formers and back formers according to
ordered set, instruction manual, steel case.
ROLLER'S Arco 50: Electric pipe bending machine, square driver
35 – 50, support 35 – 50, insert bolt, instruction
manual, transport crate.
ROLLER'S Arco 22 V: Arco 22 V: Arco 22 V Cordless pipe bending machine, Li-Ion battery, Cordless pipe bending machine, Li-Ion battery,
rapid charger, insert bolt, bending formers and
back formers according to ordered set,
instruction manual, steel case.
1.2. Article numbers
ROLLER'S Arco drive unit
ROLLER'S Arco 50 drive unit
ROLLER'S Arco 22 V drive unit Arco 22 V drive unit Arco 22 V
Square driver 35 – 50, support 35 – 50 (ROLLER'S Arco 50)
Square driver 10 – 40, support 10 – 40 (ROLLER'S Arco 50)
r, i r, insert bolt, bending formers and
580000
580100
580004 580004
582110
582120
Insert bolt
Rapid charger Li-Ion 100 – 240 V, 90 W (ROLLER'S 100 – 240 V, 90 W (ROLLER'S 100 – 240 V
Rapid charger Li-Ion 100 – 240 V, 290 W (ROLLER'S 100 – 240 V, 290 W (ROLLER'S 100 – 240 V
Li-Ion 21.6 V, 5.0 Ah battery (ROLLER'S Arco 22 V)
Li-Ion 21.6 V, 9.0 Ah battery (ROLLER'S Arco 22 V)
Power supply 220 – 240 V, 21.6 V, 40 A (ROLLER'S Arco 22 V)
ROLLER'S bending spray, 150 ml
Machine holder 3B
Machine holder WB
Steel case (ROLLER'S Arco)
Steel case (ROLLER'S Arco 22 V) Arco 22 V Arco 22 V)
Transport crate (ROLLER'S Arco 50)
Steel case (bending former and back former of ROLLER'S Arco 50) 586012
Machine cleaner
Bending formers and back formers
1.3. Applications
No cracks or wrinkles shall occur during professional cold bending. Pipe
qualities and sizes which do not guarantee this are not suited to be bent with
ROLLER'S Arco, ROLLER'S Arco 50 and ROLLER'S Arco 22 V.
Hard copper pipes are cold bendable up to Ø 18 mm according to DIN EN
1057, minimum radii must be complied with. Bending formers and back formers
for larger bending radii can be supplied.
ROLLER'S Arco
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 35 mm, Ø ⅜ –1⅜".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Thick-walled copper pipes K65 for refrigeration and air conditioning technology
EN 12735-1 Ø ⅜ – 1⅜".
● Stainless steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● C6 steel pipes, also jacketed, of the pressfi tting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼" – ¾".
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
● Composite pipes Ø 14 – 40 mm.
Largest bending angle
ROLLER'S Arco 50
● Steel pipes as per DIN EN 10255 (DIN 2440) Ø ¼" – 1¼".
● Stainless steel pipes EN ISO 1127, EN 10217-7 Ø ½ – 1¼", s ≤ 2.6 mm.
● Hard, half-hard and soft copper tubes Ø 10 – 42 mm.
● Thin walled copper tubes Ø 10 – 35 mm.
● Thick-walled copper pipes K65 for refrigeration and air conditioning technology
EN 12735-1 Ø ⅜ – 1⅝".
● Stainless steel tubes of pressfi tting systems Ø 12 – 42 mm.
● (Jacketed) C-steel pipes of the pressfi tting systems Ø 12 – 42 (28) mm.
● Composite tubes Ø 14 – 50 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
Largest bending angle
ROLLER'S Arco 22 V
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 28 mm, Ø ⅜ – 1⅛".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Thick-walled copper pipes K65 for refrigeration and air conditioning technology
EN 12735-1 Ø ⅜ – 1⅛".
● Stainless steel pipes of the pressfi tting systems Ø 12 – 28 mm.
● C6 steel pipes, also jacketed, of the pressfi tting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼ – ¾".
● Electrical installation pipes DIN EN 50086 Ø 16 – 25 mm.
● Composite pipes Ø 14 – 40 mm 40 40 mm
Largest bending angle
Operating temperature range
ROLLER'S Arco, ROLLER'S Arco 50,
ROLLER'S Arco 22 V Arco 22 V Arco 22 V
Battery
Rapid charger
Power supply Power supply Power supply
Storage temperature range
1.4. Speed Arco
Speed infi nitely
adjustable 0...4 min‫¹־‬

1.5. Electrical data

ROLLER'S Arco, 230 V, 1~, 50 – 60 Hz; 1000 W; 4.8 A or
ROLLER'S Arco 50 110 V ~; 50 – 60 Hz; 1000 W
Intermittent service S3 15% (AB 2/14 min),
double-insulated, interference-suppressed.
Protection class IP 20.
ROLLER'S Arco 22 V V V 21.6 V 21.6 V
Rapid charger Rapid charger Rapid charger
Arco 22 V Arco 22 V) Arco 22 V)
Arco 22 V Arco 22 V) Arco 22 V)
Arco 22 V Arco 22 V)
Arco 22 V Arco 22 V)
Arco 22 V) Arco 22 V
see Fig. 2
Arco 22 V Arco 22 V.
–10 °C – +60 °C (14 °F – +140 °F) –10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +104 °F)
–10 °C – +45 °C (14 °F – +113 °F) –10 °C – +45 °C (14 °F – +113 °F)
>0 °C (32 °F)
Arco 50 Arco 22 V
min‫¹־‬ min‫¹־‬ 0...1 0...1 min‫¹־‬ min‫¹־‬ min‫¹־‬ 0...3,33 0...3,33
1000 W; 4.8 A or 1000
– ---; 5.0 Ah; 21.6 V – ---; 9.0 Ah
Input Input 100 – 240 V~; 50 – 60 Hz; 90 W
Protection class II.
– ---
Output 21.6 V 21.6 21.6 V
all-insulated, interference-suppressed
eng
582036
571585 571585
571587
571581 571581
571583 571583
571578 571578
140121
586100
586150
586000
566030 566030
590160
140119
180°
90°
180°
min‫¹־‬
11