Specifications; Dolby Pro Logic - Teac AG-D9100 Bedienungsanleitung

SPECIFICATIONS

Amplifier Section
Output Power (Front):
RMS Power (40 Hz – 20 kHz):
130 watts/8 ohms, 0.09%
Surround Output Power (0.5 % THD, 1 kHz, 8 ohms):
100 + 100 watts (Front)
100 watts (Center)
100 + 100 watts (Rear)
Total Harmonic Distortion (Front):
0.02 % (at 120 watts, 1 kHz)
Delay Time:
DOLBY PRO LOGIC: 15 – 30 ms
DOLBY DIGITAL: 0 – 15 ms
Audio Input Sensitivity/Impedance:
PHONO: 2.5 mV/47 k ohms
* LINE: 220 mV/47 k ohms
Output Level/Impedance:
TAPE 1/2 REC: 200 mV/2.2 k ohms
Frequency Response:
PHONO: 20 Hz – 20 kHz, ±1 dB
* LINE: 20 Hz – 60 kHz, +1/ –3 dB
Signal-to-Noise Ratio:
PHONO: 70 dB (IHF-A)
LINE: 90 dB (IHF-A)
*
Tone Control:
BASS: ± 10 dB at 100 Hz
TREBLE: ± 10 dB at 10 kHz
Digital Audio Section
Sampling Frequency: 32 kHz, 44.1 kHz, 48 kHz
DIGITAL Input Level/Impedance:
VIDEO 1 (OPTICAL): –15 dBm — –21 dBm
VIDEO 2 (COAXIAL): 0.5 Vp-p / 75 ohms
FM Tuner Section
(Without notes 100.1 MHz, 65 dBf)
Tuning Range:
87.5 MHz – 108.0 MHz (50 kHz steps)
Usable Sensitivity (IHF):
Mono: 15 dBf
50 dB Quieting Sensitivity:
Mono: 23 dBf
Stereo: 40 dBf
Capture Ratio:
2.0 dB
Image Rejection Ratio:
40 dB
AM Suppression Ratio:
40 dB
Total Harmonic Distortion (1 kHz):
Mono: 0.4%
Stereo: 0.5%
Frequency Response:
30 Hz – 15 kHz, +1/ –1.5 dB
Stereo Separation (1 kHz):
40 dB
Signal-to-Noise Ratio:
Mono: 68 dB
Stereo: 65 dB
AM Tuner Section
Tuning Range:
522 kHz – 1,620 kHz (9 kHz steps)
Usable Sensitivity: 55 dB/m
Total Harmonic Distortion: 0.8% at 85 dB/m
Signal-to-Noise Ratio: 45 dB at 85 dB/m
Video Section
Input Sensitivity/Impedance: 1.0 Vp-p/75 ohms
Output Level/Impedance: 1.0 Vp-p/75 ohms
General
Power Requirements:
230 V AC, 50 Hz
Power Consumption:
320 W
AC Outlets:
Switched x 2, 100 W max.
Dimensions (W x H x D): 435 x 150 x 345 mm
Weight (net): 11.0 kg
Standard Accessories:
AM Loop Antenna x 1
FM Lead-type Antenna x 1
Remote Control Unit (UR-412) x 1
* LINE means CD, MD/TAPE 1, TAPE 2, VIDEO 1, VIDEO
2, VIDEO 3 and VCR/VIDEO 4.
... Improvements may result in specifications and features
changing without notice.
... Illustrations may differ slightly from production models.
– 27 –