Peg Perego Pliko P3 Modular e Gebrauchsanleitung Seite 24

the Ganciomatic connectors on the stroller, lift the
fabric covering at the corners of the seat, pull the
lever outwards and at the same time swivel the
two connectors upwards until they click (fig_a).
To lower the stroller Ganciomatic fasteners, pull
the lever outwards and at the same time rotate the
fasteners downwards (fig_b).
1 6• PLIKO P3 + Navetta XL: To attach the Navetta XL
to the stroller (fig_a):
- Apply the stroller brakes.
- Completely lower the stroller backrest.
- Raise the stroller Ganciomatic fasteners.
- Remove the front bar and insert the caps provided
to close the stroller armrests.
- Raise the footrest to the highest position.
- Take hold of the handle of the Navetta XL.
- Place it on the Ganciomatic connectors of the
stroller, with the head end of the Navetta XL on
the opposite side to the handles of the stroller.
- Press on the sides of the Navetta XL with both
hands until it clicks into place.
- To see how to release the Navetta XL from the
chassis and for further information, consult its user
manual.
PLIKO P3 + Primo Viaggio tri-fix es: To attach
the car seat to the stroller (fig_b):
- Apply the stroller brakes.
- Completely lower the stroller backrest.
- Raise the stroller Ganciomatic fasteners.
- Position the car seat facing the person pushing
and push it down until it clicks into position.
- It is important not to remove the front bar of
the stroller when attaching the car seat (for the
attachment of the front bar see point 32).
- To release the car seat from the stroller see the
instruction manual for the car seat.
TO CONVERT
THE STROLLER INTO A CHASSIS
To transform the stroller into a chassis, first the
covers must be removed (see points 38-39).
Uncover the stroller, unfastening the cover fixtures
from the armrests.
Detach the side cover button. Unthread the leg
divider strap of the harness from under the seat.
Unfasten the cover buttons from the seat and slide
the cover off to extract it from the footrest hooks.
Pull the cover upwards to remove it.
1 7• Release the base by pressing the button located
at the rear of the chassis (fig_a), both on the right
and left bars. Lift the backrest upwards from the
base with both hands.
Press the two buttons on the chassis seat with both
hands and lift the entire base upwards (fig_b).
1 8• IMPORTANT: in order to attach the hood it is
necessary to remove the protectors on both sides
P3Modular&P3OnTrackModular-EU_FI24 24
All manuals and user guides at all-guides.com
of the stroller, as shown in figure A.
Keep the protectors in a safe place so that they
can be refitted if you decide to remove the hood.
When refitting them take care to distinguish
between the left and right protectors for correct
attachment. Attach them so that the tabs remain
outside, as shown in figure B.
1 9• HOOD: To fit the hood, push the side connectors
down until they click (Fig. a), then button the hood
to the inside of the armrest (Fig. b)
2 0• a nd to the backrest of the stroller (Fig. c). To
remove the hood (Fig. d), release the side
connectors, then undo the buttons on the inside
of the armrest and the backrest of the stroller.
2 1• It is possible to detach the rear section of the hood
by undoing the zip. This also allows it to be used
as a sun canopy (Fig. a). Fasten the zip to reattach
the rear section (Fig. b).
2 2• When the stroller backrest is lowered, the rear
section of the hood extends. Thanks to the two-
way zip, it is possible to create a window that
allows more air to flow through and lets you keep
an eye on the child when he/she is asleep.
2 3• P liko P3 Modular COVER:
To fit the cover on the stroller, zip it to the leg rest
(Fig. a), fasten the buttons on both sides (Fig. b) and
put it into position, covering the front bar (Fig. c).
2 4• D epending on the model you have purchased,
there are 3 different ways of correctly attaching
the cover.
2 5• P liko P3 On Track Modular COVER:
This can be used with and attached to both the
Navetta XL and the Pliko P3 stroller. To fit it on the
Navetta XL, consult its user manual.
To fit it on the stroller, open up the cover inside to
make room for the child's legs (Fig. a).
Put it into position. Cover the front bar, fasten the
buttons on the front (Fig. b) and insert it under the
leg rest (Fig. c).
2 6• R AIN CANOPY: to fit the rain canopy, extend it over
the stroller and snap fit the buttons on both sides
of the hood (Fig.a).
Attach the elastic straps to the frame in the lower
part of the stroller (Fig_b).
• Do not use the rain canopy in closed environments
and always check that the child is not too hot.
• Do not leave the rain canopy near hear sources
and take care with cigarettes.
• Check that the rain canopy does not interfere with
any of the moving mechanisms of the stroller.
• Always remove the rain canopy before closing the
stroller.
• Wash with a sponge and soapy water, without
using detergents.
2 7• 5-POINT SAFETY HARNESS: To fasten the harness,
push the two waist strap buckles (with the
shoulder straps attached as shown by arrow a) into
the leg divider strap until they click into position
(arrow b). To unfasten it, push the round button
in the centre of the buckle upwards (arrow c) and
pull the waist straps outwards (arrow d).
2 8• T o tighten the waist strap, pull in the direction of
the arrow on both sides (Fig. a). To loosen it, do the
- 24 -
11-02-2010 17:12:49