Makita VC007GL Betriebsanleitung Seite 18

Installing or removing cleaner
attachments
CAUTION:
After installing an attachment,
check if it is securely installed. If the attachment
is installed imperfectly, it may come off and cause
personal injury.
Attachments without lock function
Optional accessory
Insert an attachment into the suction inlet of the cleaner
by pushing and hand screwing it in place.
Hand twist and pull the attachment apart from the suc-
tion inlet after use.
► Fig.19
Installing MAKPAC
Optional accessory
CAUTION:
Do not stand on or sit on the top of
the appliance. It may fall down because of instability.
CAUTION:
Be careful with the operation when
installing MAKPAC. Failing to do so may result in
personal injury or damage to the appliance.
CAUTION:
When MAKPAC is installed on the appli-
ance, do not lift the appliance with the handle of MAKPAC.
CAUTION:
When moving the appliance which is
installed MAKPAC, do not push MAKPAC but the body
of appliance. Pushing MAKPAC may break the latches
and drop MAKPAC, which may result in personal injury.
Connectable and stackable MAKPAC storage cases can
be installed on top of the cleaner. The cases are available
in many sizes and styles to suit your preferences.
1. Unfold the latches on top surface of the cleaner.
► Fig.20: 1. Latch
2. Mount the MAKPAC cases on top of the cleaner
and fix it with latches.
► Fig.21: 1. Latch 2. MAKPAC
Maximum height and weight of installing MAKPAC are
315 mm and 20 kg respectively.
► Fig.22
WIRELESS ACTIVATION
FUNCTION
Optional accessory
What you can do with the wireless
activation function
The wireless activation function enables clean and
comfortable operation. By connecting a supported tool
to the cleaner, you can run the cleaner automatically
along with the switch operation of the tool.
► Fig.23
NOTICE:
Be sure to refer to the instruction man-
ual of the tool when using the cleaner with wire-
less activation function.
NOTICE:
Do not disassemble or tamper with the
wireless unit.
NOTICE:
To prevent dust coming into the slot
of the wireless unit, always close the lid securely
during operation and storage.
NOTICE:
Do not press the wireless activation
button too hard and/or press the button with an
object with a sharp edge.
NOTE: Wireless activation needs Makita tools
equipped with the wireless unit.
NOTE: Prior to the initial use of the wireless activation
function with each tool, the tool registration is required.
Once the registration is finished with the tool, the
re-registration is not required unless it is cancelled.
NOTE: Before registration, be sure that the wireless
unit is properly inserted.
NOTE: One wireless unit can register up to 10 links
with other wireless units. If more than 10 other wire-
less units are registered to one wireless unit, the one
registered earliest will be cancelled automatically.
NOTE: The position of the wireless activation button
varies depending on the tool.
NOTE: The cleaner also starts by pressing the power
button when the stand-by switch is set to "AUTO".
However the power button will not actuate when the
wireless activation function is used.
Installing the wireless unit
WARNING:
wireless unit at the first time only. Never open the
lid after installing it.
CAUTION:
Place the cleaner on a flat and
stable surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the cleaner
before installing the wireless unit. Dust or dirt may cause
malfunction if it comes into the slot of the wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such as
a metallic part, before picking up the wireless unit.
NOTICE:
When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1. Loosen the screw to open the lid on the cleaner as
shown in the figure.
► Fig.24: 1. Lid 2. Screw
2. Insert the wireless unit to the slot.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
► Fig.25: 1. Wireless unit 2. Projection 3. Lid
4. Recessed portion
3.
Tighten the screw completely to close the lid.
18 ENGLISH
Open the lid when you install the