Inglesina APTICA SYSTEM QUATTRO Bedienungsanleitung Seite 36

fig. 47 Fit the ends of the back straps (E4) and of the waist
straps (E5) in the central buckle (E6).
fig. 48 Always use the waist strap together with the back
harness, adjusting both of them properly.
Caution! Failure to observe this precaution could cause
your baby to fall or slip, risking injury.
Caution: adapt the height and the length of the harness
according to the baby's growth.
ATTACHING THE HANDRAIL
fig. 49 To attach the bumper bar (G), fit it in the dedicated
housings (G2) in the stroller seat until it clicks into place.
fig. 50 The handrail can be open on one side or fully
removed; to open it, press the button (G1) and remove it
from its housing; to remove it, repeat the procedure on the
other side.
ATTACHING THE STROLLER HOOD
fig. 51 To secure the hood (J), go next to the side joints
(J1) on the stroller seat, fit the strap (J2) and push strongly
until it clicks completely.
fig. 52 First button the press studs (J3) to the side joints
(J1), then all rear buttons (J4) to the backrest.
fig. 53 To adjust the hood, simply accompany it to the
desired position.
fig. 54 The hood features an additional fabric insert
and sun shade that extend the degree of cover, improving
protection from the sun.
DETACHING THE HOOD FROM THE STROLLER
fig. 55 To remove the hood (J) from the stroller seat,
remove all the buttons (J4) that secure it to the backrest.
fig. 56 Remove the two snap fasteners (J3) that secure the
hood to the side joints (J1), then pull the internal strap (J2)
from the joints, pulling it firmly from both sides.
HOOD LINING MAINTENANCE
The hood lining can be removed to allow for its correct
maintenance.
fig. 57 Once the hood is released from the stroller, simply
pull out the internal strap (J2).
CLOSING THE CHASSIS WITH THE STROLLER SEAT
ATTACHED (STROLLER CONFIGURATION)
The chassis can be closed with the stroller seat attached,
both facing the parent and facing the street.
Facing the parent
fig. 58 Before closing the stroller, fold the hood, recline
the backrest to its most horizontal position, and then fully
close the stroller, as detailed above.
Facing the street
fig. 59 Before closing the stroller, fold the hood and bring
the backrest fully forward, then fully close the stroller as
detailed above.
COMFORT COVER
The All Season stroller seat is equipped with Comfort Cover
as standard outfit.
The cover, designed to make the child's walk more
comfortable as well as to guarantee extra protection during
the colder season, can be easily removed.
fig. 60 To remove it, simply undo the two snap fasteners
(E7) that lock the side panels of the upholstery to the chassis,
thus releasing the two side anchors (E8).
fig. 61 Remove the back straps from both shoulder
straps, then pull them and the lumbar straps out of the slots
provided.
fig. 62 Remove the cover (F) from the backrest by pulling
the shoulder straps out of their respective slots. Take care to
detach it correctly at the rear adjustment device (E1).
36
STROLLER SEAT LINING MAINTENANCE
It is recommended to remove the lining periodically to
provide for its correct maintenance.
To facilitate covering removal, first remove the hood, bumper
bar and the Comfort Cover.
fig. 63 Detach the two lower snap fasteners (E9) that
secure the cover to the seat.
fig. 64 Unfasten the two side buttons (E7), remove the
side panels from their seats, then the cover from the footrest.
fig. 65 Remove the crotch strap from its protective pad,
releasing it from the locking elastic, then from the slot on the
seat.
fig. 66 Pull the lower back straps out of the slots in the
centre of the backrest.
fig. 67 Unbutton the two straps (E10) that secure the
cover to the lumbar structure, then pull the two anchoring
straps (E11) out of the appropriate slots (E12).
fig. 68 Release the cover from the side hood joints, pull
the back straps out of the slots on the cover, then pull it off
the back structure.
REMOVAL/INSTALLATION OF THE SAFETY HARNESS
SYSTEM
The All Season stroller is equipped with a safety harness
system that can be removed if necessary.
fig. 69 To remove the crotch strap, pull the lower ring
(E13) out of the slot on the seat (E14).
fig. 70 To remove the lower back strap, push the belts
through the slot on the backrest (E15) and pull one portion
firmly until the ring (E16) is released from its seats. Then
remove the ring (E16) from the slot (E15) and pull the belt
out completely.
fig. 71 To remove the back straps, simply pull them off the
metal rings (E17) that secure them to the backrest tube.
fig. 72 To install the crotch strap, fit the lower ring (E13)
only in the slot on the seat (E14). The lower ring (E18) must
remain on the outside.
fig. 73 To reassemble the lower back strap, insert the ring
(E16) in the appropriate slot on the backrest and, once it
is positioned under one of the hooking tabs (E19), push it
firmly into place.
fig. 74 To reattach the back straps, wrap them individually
around the backrest tube, making sure they are not inverted
or twisted.
fig. 75 Insert each belt into its respective metal ring (E17),
taking care that they are positioned outside the backrest
adjustment device (E1).
Caution! Position the back harnesses always at the same
height.
fig. 76 Caution! Make sure that all the belts are
correctly attached to the stroller seat by pulling them
individually.
FOOTMUFF (if available)
fig. 77 Position the footmuff (L), passing it under the
bumper bar, and attach the press studs (L1).
fig. 78 The flap of the footmuff can be extended and
attached in a position suitable for protecting the child from
the cold, fastening it with the external side press studs to the
corresponding elements (L2) on the canopy.
fig. 79 The footmuff can be used both facing the parent
and facing the street.
RAIN COVER (if available)
fig. 80 To fit the rain cover (M), position it on the hood and
button both press studs (M1) on the sides of the stroller seat.
fig. 81 Then hook the bands (M2) around the front tubes,
at the wheel assembly.