Herunterladen Inhalt Inhalt Diese Seite drucken

Performing An Application (Fig. A, E) - DeWalt D25872 Bersetzt Von Den Originalanweisungen

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
Inserting and Removing SDS max® Bits
(Fig. C)
nOtE: Accessories and attachments used must be lubricated
around the SDS fitment before installation.
1. Pull back the locking sleeve 
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
nOtE: The bit needs to move several centimeters in and out
of the tool holder 
 6 
when properly engaged.
4. To remove the bit, pull back the locking sleeve and pull the
bit out.
SDS plus® and SDS max® are registered trademarks of
Robert Bosch GmbH.
Bit Position Adjustment
Turn the mode selector to bit adjustment icon (refer to Mode
Selection) to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel.
nOtE: After finding the desired position, slightly maneuver
the chisel bit back and forth to ensure the chisel is
properly engaged.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the ON/
OFF rocker switch is in the OFF position. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the mounted side
handle 
2
, with the other hand on the main handle 
Mode Selection (Fig. E)

WARNING: Do not select the operating mode when the
tool is running. Tool must come to a complete stop before
activating the mode selector dial or damage to the tool
may result.
Your tool is equipped with a mode selector dial 
mode appropriate to desired operation.
and insert the bit shank. The
 7 
5
.
 4 
to select the
symbol
Mode
Bit
adjustment
Hammering/
chiselling
To Select a Mode
Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOtE: The arrow on the mode selector dial 
at a mode symbol at all times. There are no operable positions
in between.
Indexing the Chisel Position (Fig. E)
The chisel can be indexed and locked into 24 different positions.
1. Rotate the mode selector dial 
 position.
2. Rotate the chisel in the desired position.
3. Set the mode selector dial 
Chiselling position.
4. Twist the chisel until it locks in position.
Performing an Application (Fig. A, E)

WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly.
nOtE: Operating temperature of this tool is 7 to 40˚ C. Using
the tool outside of this temperature range will decrease the life
of the tool.
1. Insert the appropriate chisel and rotate it by hand to lock it
into the desired position. Refer to Bit and Bit Holder.
2. Set the mode selector dial 
Chiselling position. Refer to Mode Selection.
3. Adjust the side handle 
the Side Handle Assembly.
4. Place the chisel on the desired location.
5. Depress the ON/OFF rocker switch 
6. To stop the hammer, release the ON/OFF rocker switch.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the ON/
OFF rocker switch is in the OFF position. An accidental
start-up can cause injury.
application
Chisel bit position adjustment
Light chiselling and demolition
 4 
must be pointing
 4 
until it points towards the
 4 
to the Hammering/
 4 
to the Hammering/
 2 
as necessary. Refer to Mounting
 1 
.
EngLIsH
21

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis