Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
Microwave radiation cannot penetrate metal; therefore do not use
metal containers or plates.
CAUTION:
•
Do not use paper bowls made of recycled material, as these might
contain small amounts of metal which might cause flying sparks or
fire.
The table below is intended to help you choose suitable tableware:
Material
Microwave
Heat-resistant glass
yes
container
Non heat-resistant
no
glass container
Heat-resistant ceramic
yes
container/plate
Plastic containers suit-
yes
able for microwaves
Kitchen paper
yes
Supplied enamelled
yes
plate
Metal or aluminium
no
ovenware
Grill
no
Aluminum foil or alumi-
no
num foil containers
*) Combination of microwave and grill or microwave and convection
Notes on Operating and Using the Appliance
Important information on the operation of microwaves
•
Your device operates with microwave radiation which heats water
particles in food very quickly. There is no heat radiation and there-
fore hardly any browning.
•
Use this device to heat food only.
•
The device is not suitable for deep-frying.
•
Heat 1-2 servings at a time. Otherwise the device will not work
efficiently.
•
Microwaves provide full power instantly. Pre-heating is therefore not
necessary.
•
Never operate the device empty during microwave operation.
•
The microwave is not a replacement for your common stove. It is
mainly intended for:
•
defrosting deep-frozen/frozen food
•
quickly heating food or drinks
•
cooking dishes
Operation of the device
•
A signal tone sounds when first turning the turning knob.
•
Your selection by pressing buttons is confirmed by a signal tone. If
not, you did not press properly.
•
If you set a program but do not press the START/+30SEC./CON-
FIRM button within 5 minutes, the setting will be canceled. The
display will then show the current time again.
•
When starting a program (except during pre-heating), the remaining
operating time will be displayed. The countdown runs.
•
5 signal tones will indicate the end of the program. After that the
appliance turns off automatically.
Suitable for
Convec-
Combi-
Grill
tion
nation *
yes
yes
yes
no
no
no
yes
yes
yes
no
no
no
no
no
no
yes
yes
yes
yes
yes
no
yes
yes
no
yes
yes
no
Initial Operation
Installation Instructions
•
Install the appliance with the back of the appliance facing the wall.
•
Keep the following safety distances:
•
10 cm on the back
•
20 cm on both sides
•
30 cm on the top of the microwave.
•
In order to avoid interference with the operation of other devices, do
not place your device near other electronic devices.
Preparation
•
Press the door release button to open the door of the microwave.
The door will swing open.
•
Remove all accessories found in the cooking chamber and unpack
them.
•
Place the metal tray with its dents on the bottom locking into the
center of the drive shaft.
•
When using a pizza stone, first install the guide ring on the drive
shaft and then place the pizza stone onto the guide ring.
•
Check the device for visible damage, especially in the area at and
around the door. It is imperative not to use the device in case of any
damage.
•
Remove protective sheets that might be attached to the enclosure.
•
Check if the mains voltage to be used matches the voltage of the
appliance. Refer to the rating label for detailed specifications.
•
Connect the plug to a properly installed isolated ground receptacle.
CAUTION:
•
Do not remove mounted parts from the cooking chamber or inside
of the door!
•
The mica sheet is also part of the appliance and must not be
removed. It protects the electronic component located behind it
from dirt.
NOTE:
If there are manufacturing or oil remains on the enclosure or heating
element, smoke or odor might occur during the beginning operation.
This is normal and will cease after repeated use.
We strongly recommend proceeding as follows:
•
Turn on the grill mode and let the device operate several times
without food to be cooked.
•
Ensure sufficient ventilation.
Setting the clock
NOTE:
When connecting the appliance to the mains, a signal will sound and
"0:00" will appear in the display.
1. Press the CLOCK/PRE-SET button once or repeatedly in order to
toggle between 24 hour and 12 hour display mode.
2. Use the turning knob to set the desired hour.
3. Press the CLOCK/PRE-SET button to confirm your settings.
4. Use the turning knob to set the desired minutes.
5. Press the CLOCK/PRE-SET button again to activate the new time.
The delimiter symbol ":"of the digital time will be flashing on the
display.
75
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
