Gaggenau VG295150F Montageanleitung Seite 10

EN 10226 R 1/2 conical
¡
Use one of the supplied connection elbows and the
corresponding seal to connect the appliance to a
fixed power cable or a gas safety hose.
The gas safety hose should have a length of at least
1 m up to a maximum of 3 m.
Observe the information about the gas safety hose:
If the gas safety hose is made of metal, the per-
¡
missible ambient temperature is 115 °C. If the
gas safety hose is not made of metal or is only
partially made of metal, the ambient temperature
must not exceed 90 °C.
The gas safety hose must not come into contact
¡
with moving parts of the fitted unit (e.g. drawers)
or be routed in areas where it could become
trapped or damaged.
The gas safety hose must not come into contact
¡
with a hob, oven, dishwasher, refrigerator, wash-
ing machine, hot water pipes, radiator or any other
appliance installed next to or below the gas hob.
The gas safety hose must not be subject to rub-
¡
bing, vibrations, kinking or any other kind of de-
formation. It should be checked along its entire
length with the hob in the installation position.
Information about the electrical
connection
In order to safely connect the appliance electrically,
observe this information.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appli-
ance from the electricity supply. The appliance must
only be connected to a protective contact socket
that has been correctly installed.
The mains plug of the mains power cable must be
▶
easily accessible after installation of the appliance.
If this is not possible, an all-pole isolating switch
▶
must be integrated into the permanent electrical
installation according to the conditions of over-
voltage category III and according to the installa-
tion regulations.
The permanent electrical installation must only be
▶
wired by a professional electrician. We recom-
mend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
Sharp-edged or hot components inside the appli-
ance may damage the connection cable.
Do not kink or trap the connection cable.
▶
Do not route the connection cable along hot sur-
▶
faces.
Incorrect repairs are dangerous.
Repairs to the appliance should only be carried
▶
out by trained specialist staff.
Only use genuine spare parts when repairing the
▶
appliance.
If the power cord of this appliance is damaged, it
▶
must be replaced with a special connection cable,
which is available from the manufacturer or his
Customer Service.
Ensure that the information on the rating plate re-
¡
garding the output and voltage complies with the
local connection conditions.
The appliance corresponds to protection class 1.
¡
You should therefore only use the appliance with
a protective earth connection.
Do not connect the appliance to the power supply
¡
during installation.
Ensure that the protection against contact is guar-
¡
anteed during installation.
Only a qualified electrician may connect appli-
¡
ances without a plug. They are subject to the re-
quirements of the local electricity provider.
10
Do not use the appliance with an external timer or
¡
a remote control.
The appliance must only be connected using the
¡
power cable provided.
Information on fitted units
Observe the cut-out dimensions and the installation
instructions when installing in a worktop.
The fitted units must be heat-resistant to at least
90 °C.
Ensure that the stability of the fitted unit is guaran-
teed after the cut-outs have been made.
The cut-out edges at the sides must be at least
20 mm thick and flat to ensure that the retaining
springs sit correctly on the appliance. For multi-layer
worktops, affix appropriate strips to the side in the
unit cut-out, if required.
Use suitable substructures to ensure the load-bear-
ing capacity and stability of the unit. Take the appli-
ance weight, including additional load, into consider-
ation. Ensure that the reinforcing material is heat-
and moisture-resistant.
To improve flame stability, install an intermediate
floor underneath the appliance in the installation cab-
inet.
Observe the position of the gas
connection
Observe the position of the gas connection when
▶
installing the appliance.
→ Fig.
4
Preparing the appliance
Screw the corresponding connection elbow with
▶
the seal onto the appliance.
→ Fig.
5
Preparing the unit
Requirement: The fitted units must be heat-resistant
up to 90 °C.
Ensure that the stability of the fitted unit is guaran-
1.
teed after the cut-outs have been made.
Mark the unit cut-out in accordance with the in-
2.
stallation diagram.
→ Fig.
6
Drill four holes with a diameter of 6 mm.
3.
→ Fig.
7
Ensure that the angle of the cut surface to the
4.
worktop is 90°.
→ Fig.
7
Ensure that the cut-out edges at the sides are at
5.
least 20 mm thick and flat to ensure that the re-
taining springs sit correctly on the appliance.
→ Fig.
8
For multi-layer worktops, affix appropriate strips to
6.
the side in the unit cut-out, if required.
After making the cut-outs, remove any shavings.
7.
Seal the cut surfaces so that they are heat-resist-
8.
ant and waterproof.
→ Fig.
7
Observe the minimum clearance of 10 mm
9.
between the bottom of the appliance and unit
parts.
Use suitable substructures to ensure the load-
10.
bearing capacity and stability of the unit, particu-
larly in the case of thin worktops.
Take the appliance weight, including additional
‒
load, into consideration.
Use heat-resistant and moisture-resistant rein-
‒
forcement material.