Specifications; Specific Safety Rules - Makita 9561CVR Betriebsanleitung

ENGLISH
1. Shaft lock
2. Slide switch
3. Indication lamp (speed adjusting
dial)
4. Indication lamp
5. Speed adjusting dial
6. Wheel guard
7. Bearing box

SPECIFICATIONS

Depressed center
wheel diameter
Spindle thread
Rated speed (n) / No load speed (
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Note: Specifications may differ from country to country.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. DOUBLE INSULATION
............. Wear safety glasses.
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to grinder
safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1. Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off
Operations:
Explanation of general view
8. Screw
9. Lever
10. Lock nut
11. Depressed center grinding wheel/
Multi-disc
12. Inner flange
13. Lock nut wrench
14. Diamond wheel
115 mm M14 9561CR
125 mm M14 9562CR
n
) 11,000 (min
o
289 mm
END202-4
ENE048-1
ENF002-1
GEB033-1
9564CR
9565CR
-1
) 11,000 (min
299 mm
1.8 kg 1.8 kg
2. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
3. Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
4. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
5. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
6. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
7. The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
8. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked
15. Spindle
16. Marking A
17. Marking B
18. Marking C
19. Pin
20. Vent
21. Exhaust vent
22. Inhalation vent
9561CVR
9562CVR
2,800 - 11,000
-1
)
-1
(min
)
289 mm
1.8 kg
/II
9564CVR
9565CVR
2,800 - 11,000
-1
(min
)
299 mm
1.8 kg
5