Makita DTW284 Betriebsanleitung Seite 7

NOTE: When the LED display goes off, the tool is
turned off to save the battery power. To check the
remaining battery capacity, slightly pull the switch
trigger.
NOTE: The LED display goes off approximately one
minute after releasing the switch trigger.
NOTE: When the LED display lights up and the tool
stops even with a recharged battery cartridge, cool
down the tool fully. If the status will not change, stop
using and have the tool repaired by a Makita local
service center.
NOTE: When the tool is overheated, the light flashes
for one minute, and then the LED display goes off. In
this case, cool down the tool before operating again.
Switch action
► Fig.5: 1. Switch trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
NOTE: The tool automatically stops when you keep
pulling the switch trigger for 3 minutes.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
► Fig.6: 1. Lamp
► Fig.7: 1. Button
Changing the impact force/mode
► Fig.9: 1. Changed in four steps 2. Hard impact
mode 3. Medium impact mode 4. Soft impact
mode 5. Reverse rotation auto stop mode
6. Button
You can change the impact mode in four steps: hard,
medium, soft, and reverse rotation auto stop mode.
To select the step, press the button
Specifications of each impact force grade
Impact force grade displayed
on panel
Hard
Medium
.
Maximum blows
-1
3,500 min (/min) Tightening when force and
speed are desired.
-1
2,600 min (/min) Tightening when you need
good controlled power.
7 ENGLISH
To turn on the lamp status, press the button
one second. To turn off the lamp status, press the but-
ton for one second again.
With the lamp status ON, pull the switch trigger to turn on
the lamp. To turn off, release it. The lamp goes out approx-
imately 10 seconds after releasing the switch trigger.
With the lamp status OFF, the lamp does not turn on
even if pulling the trigger.
NOTE: To confirm the lamp status, pull the trigger.
When the lamp lights up by pulling the switch trigger,
the lamp status is ON. When the lamp does not come
on, the lamp status is OFF.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE: While pulling the switch trigger, the lamp
status cannot be changed.
NOTE: For approximately 10 seconds after releasing
the switch trigger, the lamp status can be changed.
Reversing switch action
► Fig.8: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the direc-
tion of rotation before the tool stops may damage the tool.
CAUTION:
When not operating the tool, always
set the reversing switch lever to the neutral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
For approximately one minute after releasing the switch
trigger, the impact force can be changed.
Hard, Medium, and Soft impact mode allows a tighten-
ing suitable to the work.
The function of reverse rotation auto stop mode works
only with pulling the trigger fully in counterclockwise tool
rotation. When the bolt/nut gets enough loosened, the
tool stops the impact and rotation.
Application
for
Work
Assembling the steel frame.
Assembling or disassembling
scaffolds or framework.