Technical Data; Before Starting The Equipment; Operation - EINHELL BG-EL 2300/1 Originalbetriebsanleitung

Anl_BG_EL_2300_1_2500_2E_SPK7__ 08.10.14 15:08 Seite 13

4. Technical data

AC motor
Output BG-EL 2100
no load speed n
0
7000-15000 min
Protection class
Air velocity
Suction rate
Volume of debris bag
Sound volume level L
WAd
Sound pressure level L
pAd
Vibration a
hv
Weight

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the suction tube (Fig. 3a-3d)
First plug together the front suction tube (1), the rear
suction tube (2) and the rear blower tube (3) (Fig. 3a).
Then screw together the tubes using the screws
provided (Fig. 3b/Item 11).
Finally, plug the suction tube into the motor housing
(Fig. 3c) and screw it in place with the screw (Fig.
3d/Item 11) and with one screw on each side (Fig.
3d/Item 12).
Note: Do not disassemble the suction tube any
more once it has been assembled.
5.2 Fitting the debris bag (Fig. 3e-3f)
First hang the eyelet on the hook on the suction tube
(Fig. 3e). Then slip the debris bag (Fig. 3f/Item 7) over
the port on the motor housing. Make sure that there is
an audible click when they engage.
5.3 Fitting the carrying strap (Fig. 3g)
Pass the carrying strap (Fig. 2/Item 4) through the
metal eyelet as shown in Fig. 3g and close the quick
fastener.
230 V ~ 50 Hz
2300 watts (BG-EL 2300/1)
2500 watts (BG-EL 2500/2 E)
15000 min -1 (BG-EL 2300/1)
-1 (BG-EL 2500/2 E)
II / ®
240 km/h
780 m
approx. 40 l
103 dB (A)
83 dB (A)
≤ 2.5 m/s
3.1 kg
Start up the equipment only when fully assembled.
Always inspect the power cable for damage before
starting up. The equipment may be used only if the
cable is in flawless condition.

6. Operation

6.1 Sizing the strap (Fig. 1)
Size the length of the carrying strap (4) so that the
vacuum tube just clears the ground. The guide rollers
(9) at the bottom end of the suction tube will help you
3 /h
to maneuver the suction tube on the ground.
6.2 Connecting the equipment to the power
supply and switching on (Fig. 4, 5)
The equipment can be connected to any socket-outlet
(with 230 V AC) that is equipped with a 10A fuse or
2
higher. The socket-outlet has to be safeguarded by an
earth-leakage circuit breaker (e.l.c.b.). The operating
current must not exceed
30 mA.
Insert the equipment's plug into the power cable
n
coupling (extension).
Secure the power cable with the strain-relief clip
n
provided on the equipment as shown.
To switch on, push the On/Off switch (Fig. 5/Item
n
5) toward "I".
To switch off, push the On/Off switch (Fig. 5/Item
n
5) toward "O".
6.3 Selecting the mode of operation
6.3.1 Suctioning (Fig. 6)
Turn the lever (Fig. 6/Item 8) to position A. You can do
this both when the equipment is at a standstill and
while it is running.
6.3.2 Blowing (Fig. 6)
Turn the lever (Fig. 6/Item 8) to position B. You can
n
do this both when the equipment is at a standstill
and while it is running.
Channel the air stream forward and walk slowly to
n
blow foliage or garden refuse into a pile or to clear
out hard-to-reach places.
Caution!
n
Empty the debris bag before blowing. Otherwise,
the material that has been vacuumed up could
drop out.
GB
13