Safety Instructions For Maintenance; Operation - Husqvarna BMP 215 Bedienungsanweisung

• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Fuel on your skin can cause injury. If you get fuel on
your skin, use soap and water to remove the fuel.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Before you start the product, move the product to a
minimum of 3 m/10 ft from where you refueled.
• Do not start the product if there is fuel or engine
oil on the product. Remove the unwanted fuel and
engine oil and let the product dry before you start the
engine.
• Examine the engine for leaks regularly. If there are
leaks in the fuel system, do not start the engine until
the leaks are repaired.
• Do not use your fingers to examine the engine for
leaks.
• Keep fuel in approved containers only.
• When the product and fuel is in storage, make sure
that fuel and fuel fumes cannot cause damage.
• Drain the fuel in an approved container outdoors and
away from sparks and flames.

Safety instructions for maintenance

WARNING:
instructions that follow before you use the
product.
Introduction
WARNING:
product, you must read and understand the
safety chapter.
To do before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. BMP 215Petrol: Read the operator's manual for the
combustion engine carefully and make sure that you
understand the instructions.
3. Read the operator's manual for the dust extractor
carefully and make sure that you understand the
instructions.
4. Use personal protective equipment. Refer to
Personal protective equipment on page 27 .
5. Make sure that only approved persons are in the
work area.
30
Read the warning

Operation

Before you operate the
• Use personal protective equipment. Refer to
Personal protective equipment on page 27 .
• Only do the maintenance as given in this operator's
manual. Let an approved service agent do all other
servicing.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Clean the product to remove dangerous material
before you do the maintenance.
• Before you do the maintenance, stop the product
and prevent accidental start:
• BMP 215: Stop the motor, pull out the operator
presence control and disconnect the power plug.
• BMP 215Petrol: Stop the engine and pull out the
operator presence control.
• Do the maintenance of the product on stable level
ground.
• Do not do modifications to the product. Modifications
that are not approved by the manufacturer can
cause serious injury or death.
• Replace damaged, worn or broken parts.
• Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
• After maintenance, do a check of the vibration level
in the product. If it is not correct, speak to an
approved service agent.
• Let an approved service agent do servicing on the
product regularly.
6. Do daily maintenance. Refer to
schedule on page 32 .
7. Make sure that the product is assembled correctly
and is not damaged.
8. Put the product on the work area. Make sure that the
surface is level. Make sure that the transportation of
the product to and in the work area is done safely
and correctly. Refer to
9. Make sure that the scarifying drum does not hit the
ground.
10. Make sure that the cutters can move freely on the
axle of the scarifying drum.
11. Connect a dust extractor to the product. Refer to
connect a dust extractor on page 31 .
12. BMP 215: Connect the product to a power source.
To connect the product to a power source
Refer to
BMP 215 on page 31 .
13. BMP 215Petrol: Fill the fuel tank. Refer to
BMP 215Petrol on page 31 .
14. BMP 215Petrol: Do a check of the oil level. Refer to
the operator's manual for the combustion engine.
Maintenance
Transportation on page 35 .
To fill fuel
1819 - 002 - 07.04.2022
To