Herunterladen Inhalt Inhalt Diese Seite drucken

Suggestions And Recommendations; Maintenance And Cleaning - Whirlpool WT 1090 BA Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 144
Activation of the function
To activate the function, select the plate, and press the 6th SENSE sensor (17) until the led (19) located on the icon / lights up. Once the feature is
activated, the sign will appear on the power indicator (3); a moving segment will appear, indicating that the cooking is under the system's
control. When the system detects that it is about to start boiling, a first beep will be heard.
Take this opportunity to prepare your food for boiling or baking as desired. After 30 seconds, a second beep will be heard; if you have not already
done so, it's time to pour the food in the pan. After the second beep, the system will activate the timer and stopwatch for you so that you can
control how long the food is to be boiled.
30 seconds after activating the stopwatch, a third beep will sound to warn that from that moment on, the system will decrease the power supplied
in order to maintain a gentle and continuous boil. The timer will remain active until the end of cooking.
If desired, you can disable the timer and set a time for the countdown and automatic shutdown of the plate (see section Timer Function).
Deactivation of the function
You can override the function at any time by turning off the plate, by changing the power level or by choosing a different special function.

SUGGESTIONS AND RECOMMENDATIONS

Use pots or pans with thick, completely flat bottoms.
Do not slide pots and pans over the glass because they could
scratch it.
Although the glass can take knocks from large pots and pans
without sharp edges, try not to knock it.

MAINTENANCE AND CLEANING

WARNING
!
Do not use steam cleaning equipment.
Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator ("H") is not displayed.
Important:
Do not use abrasive sponges or scouring pads as they may damage the glass.
After each use, clean the hob (when it is cool) to remove any deposits and stains from food residue.
A surface that is not kept suitably clean may reduce the sensitivity of control panel buttons.
Use a scraper only if residues are stuck to the hob. Follow the scraper manufacturer's instructions to avoid scratching the glass.
Sugar or foods with a high sugar content can damage the hob and must be immediately removed.
Salt, sugar and sand could scratch the glass surface.
Use a soft cloth, absorbent kitchen paper or a special hob cleaner (follow the Manufacturer's instructions).
Spills of liquid in the cooking zones can cause the pots to move or vibrate.
After cleaning the hob, dry thoroughly.
TROUBLESHOOTING
Check that the electricity supply has not been shut off.
If you cannot turn the hob off after using it, disconnect it from the power supply.
If alphanumeric codes appear on the display when the hob is switched on, consult the following table for instructions.
Please note: The presence of water, liquid spilled from pots or any
objects resting on any of the hob buttons can accidentally activate or
deactivate the control panel lock function.
If something does not work
Before calling the technical service, perform the verifications
described below.
The appliance does not work:
Ensure that the power cable is plugged in.
The induction zones do not produce heat:
The container is not appropriate (it does not have a
ferromagnetic bottom or is too small). Check that the bottom of the
container attracts a magnet, or use a larger container.
A humming is heard when starting to cook in the induction zones:
With containers which are not very thick or not in one piece,
the humming results from the transmission of energy directly to the
bottom of the container. The humming is not a defect, but if you wish
to avoid it anyway, reduce the power level slightly or use a container
with a thicker bottom, and/or of one piece.
To avoid damaging the ceramic glass surface, do not drag pots and
pans over the glass and keep the undersides of them clean and in
good condition.
Recommended diameters of the pot bottom (see ''Technical Data
Sheet'' supplied with the product).
The touch control does not light up or, despite lighting, does not
respond:
No heating zone has been selected. Be sure to select a heating zone
before operating it. There is humidity on the sensors,and/or your fingers
are wet. Keep the touch control surface and/or your fingers clean and
dry. The locking function is activated. Unlock the controls.
The sound of a fan is heard while cooking, which continues even
after cooking has ended:
The induction zones have a fan to keep the electronics cool. This only
operates when the electronic circuits get hot. It stops again when the
circuits cool whether the hob is turned on or not.
The symbol will appear
induction system does not find a pot or pan on a hotplate or it is of an
unsuited type.
The hotplate will switch off and the message:
on the power indicator of a hotplate: The

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis