Black & Decker KA88 Originalanweisung Seite 6

English
(original instructions)
● Wear ear protectors. Exposure to noise can cause
hearing loss.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
@
preliminary assessment of exposure.
WARNING! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the
tool is used. The vibration level may increase above
the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
:
WARNING! To reduce the risk of injury, the user
must read the instruction manual.
#
Electrical safety
This charger is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
● If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Lock-on button
3. Adjustable handle
4. Tension lever
5. Retractable hood
6. Centring knob
7. Dust extraction outlet
@
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
@
Fitting a sanding belt (fig. A)
Warning! Never use the tool without a sanding belt.
● Pull the tension lever (4) outward to release the tension on
the sanding belt (8).
● Remove the old sanding belt.
6
● Place a new sanding belt over the rollers. Ensure that the
arrow on the sanding belt points in the same direction as
the arrow on the tool.
● Push the tension lever (4) inward to tension the
sanding belt.
Adjusting the sanding belt tracking (fig. B)
To ensure a correct tracking, the sanding belt must be centred
over the rollers.
● Switch on the tool while holding it upside down.
● Turn the centring knob (6) as required until the tracking of
the belt is centred over the rollers.
Adjusting the handle (fig. C)
The handle is adjustable to 3 positions.
● Unlock the handle (3) by pulling the locking
handle (9) outward.
● Adjust the handle in the desired position.
● Lock the handle by pushing the locking handle inward.
Retracting the hood (fig. D)
@
The hood can be retracted for sanding in confined spaces.
Warning! The hood can only be retracted when the
adjustable handle is in the up position.
● Adjust the handle (3) in the straight-up position.
● Lift the hood (5) up.
● To close the hood, pull the tab (10) sideways first.
Fitting and removing the dust cassette (fig. E)
● Slide the dust cassette (11) over the dust extraction
outlet (7).
● To remove the dust cassette, slide it off the outlet.
Connecting a vacuum cleaner (fig. F)
● Slide the adaptor (12) over the dust extraction outlet (7).
● Connect the hose of the vacuum cleaner to the adaptor.
@
Use
Warning! Let the tool work at its own pace. Do
not overload.
Switching on and off
● To switch the tool on, press the on/off switch (1).
● For continuous operation, press the lock-on button (2) and
release the on/off switch.
● To switch the tool off, release the on/off switch. To switch
the tool off when in continuous operation, press the on/off
switch once more and release it.
Emptying the dust cassette (fig. E & G)
The dust cassette should be emptied every 10 minutes of use.
● Remove the dust cassette (11) to the rear and off the tool.
● Remove the cover (13) by twisting it clockwise.
● Hold dust cassette with the filter (14) facing down and
shake the cassette to empty the contents. Shake the
cover to empty the contents.
● Refit the cover (13) onto the dust cassette, twisting it
counterclockwise until it locks into place.
● Refit the dust cassette onto the tool.
Cleaning the dust cassette filter