Noise Emission; Dust Emission; Contents Of Delivery; Transport And Start Up - Jet JWBS-16X Gebrauchsanleitung

JWBS-18Q:
Wheel diameter
Cutting width
Cutting height
Sawblade length
Blade width
Blade thickness
Cutting speed 550 / 970 m/min
Machine Table(Lx W)
Table tilting range
Working height
Weight
Mains 230V ~1/N/PE 50Hz
Motor output power 1,5 kW (2HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Motor output power 2,2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F): 5x1,5mm²
Installation fuse protection
JWBS-20Q:
Wheel diameter
Cutting width
Cutting height
Sawblade length
Blade width
Blade thickness
Cutting speed 550 / 970 m/min
Machine Table(Lx W)
Table tilting range
Working height
Weight
Mains 230V ~1/N/PE 50Hz
Motor output power 1,5 kW (2HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Motor output power 2,2 kW (3 HP) S1
Reference current
Extension cord (H07RN-F): 5x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN
1807:1999 (Inspection tolerance 4 dB)
Workpiece beech:
T=30mm, L=1500mm, moisture 8,5%
Acoustic power level
(according to EN ISO 3746):
Idling LwA 82,5 dB(A)
Operating LwA 93,6 dB(A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA 74,7 dB(A)
Operating LpA 87,2 dB(A)
The specified values are emission
levels and are not necessarily to be
470 mm
seen as safe operating levels.
max 460 mm
Although there is a correlation
max 300 mm
between emission and imission levels,
3480 mm
these do not constitute a basis for
3 - 30 mm
determining the necessity of additional
0,5 – 0,7 mm
safety measures. Workplace
conditions which could influence the
485x485 mm
noise imission level include the
-10° to 45°
duration of resonance, spatial
950mm
particulars, other noise sources etc.
180 kg
For example, the number of machines
and other work being performed. The
permissible workplace levels can vary
8.6 A from country to country.
This information is intended to allow
16A
the user to make a better estimation
of the hazards and risks involved.
5 A

4.3 Dust emission

16A The band saw series JWBS-
16X/18Q/20Q has been dust emission
inspected.
520 mm
At an air velocity of 20 m/s on the dust
max 508 mm
port dia 100mm:
max 300 mm
Vacuum pressure
3820 mm
Volume flow
3 - 30 mm
0,6 – 0,8 mm The machine meets a workplace dust
emission of 2 mg/m³.
530x530 mm
-10° to 45°
930mm
4.4 Content of delivery
256 kg
Machine table
Fence
Fence support rails
Resaw guide
8.6 A
Mitre gauge
Assembly bag
16A
Saw blade 20mm
Operating manual
Spare parts list
5 A
16A

5. Transport and start up

5.1 Transport and installation

The machine will be delivered on an
open crate.
For transport use a forklift or hand
trolley. Make sure the machine does
not tip or fall off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine can be bolted down if
required.
For packing reasons the machine is
not completely assembled.
1250 Pa
565 m³/h
5

5.2 Assembly

If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Attach the handle (A, Fig1) to the
hand wheel (B, Fig1)
Fig 1
Mount the machine table to the
trunions and attach the lock knobs (A,
Fig 2).
Fig 2
Set the table to be square to the
sawblade and reference the table stop
(B, Fig 2) and the tilting scale (D, Fig
2).
Attach the support rails (G, Fig 3) to
the machine table with 4 hex cap
screws, 4 spring washers and 4
washers and align them parallel to the
table surface.