Balluff BNI EIP-508-105-Z067 Montageanleitung Seite 8

BNI EIP-508-105-Z067
Network interface
Construction and function
FE connection
LK1
EtherNet/IP Port 1
P
S
IN
Power supply input
BNIXXXX
US UA MOD NET
0
Port 0
00
1
Port 1
02
2
Port 2
04
3
Port 3
06
The Ethernet/IP-IO-Link master is a decentralized and
configurable gateway that processes and evaluates the
input and output signals of standard sensors and actuators
as well as process data from connected IO-Link devices.
The data is transmitted via an existing fieldbus interface to
00-19-31-XX-XX-XX
a higher-level controller set up by the user for further
LK1
processing.
A web server is available on the IO-Link master for
configuration and diagnostics.
The IO-Link master supports the Quick Connect function IP
P
S
SN
for a quick (re)connection to the Ethernet network and the
GW
3 2 1 0
DLR protocol for redundant communication in a ring
topology.
IN
Display elements
POWER
BNIXXXX BNI XXX-XXX-XXX-XXX
US UA MOD NET 100 LK1 100 LK2
0
00 01 08
1
Port/Pin LEDs
LED number
02 03 10
Even 2
Odd
04 05 12
3
06 07 14
2 english
Mounting hole
MAC-ID
00-19-31-XX-XX-XX
LK2
EtherNet/IP Port 2
IP
SN
GW
3 2 1 0
OUT
POWER
Power supply
output
BNI XXX-XXX-XXX-XXX
100 LK1 100 LK2
4
Port 4
01 08 09
5
Port 5
03 10 11
6
Port 6
05 12 13
7
Port 7
07 14 15
Mounting hole
MAC-ID
LK2
OUT
Status LEDs
4
Port/Pin LEDs:
09
Status of IO-Link und
5 I/O-Ports
Assignment
11
6 Pin 4
Pin 2
13
7
15
Display elements
Port/Pin LEDs Standard-Port
Display Meaning
Off State of input or output pins is 0
Yellow, static State of input or output pins is 1
Both LEDs Short circuit of sensor supply between
flashing red pin 1 and pin 3
Red, static Short circuit at output on pin 2/4 against
pin 3
Red, static No high signal at diagnostic input
Red, static 24 V input signal on configured output
(actuator warning)
Port/Pin LEDs IO-Link-Port
Display Meaning
Green, static IO-Link connection active
Flashing No IO-Link connection or incorrect
green IO-Link device
Green, fast IO-Link: Preoperate during data storage
flashing
Red, fast Validation failed / incorrect configuration
flashing of the IO-Link data length
Red, fast Data storage failed / incorrect device for
flashing data storage
Red, static IO-Link: Short circuit of pin 4 against
pin 3
Status LEDs
LED Signal Meaning
US Green, static Input voltage OK
Red flashing Input voltage low (< 18 V)
UA Green, static Output voltage OK
Red flashing Output voltage low (< 18 V)
Red, static No output voltage present
(< 11 V)
MOD Flashing Incorrect or no module
green configuration
Green, static Module working
Red flashing Fixed bus cycle not possible
Red/Green Starting sequence
flashing
NET Off Module has no IP address
Flashing Module has an IP address, but no
green connection established
Green, static Connection is established
Red flashing Connection timeout
Red/Green Starting sequence
flashing
100 Off Transmission rate: 10 Mbit/s
Yellow, static Transmission rate: 100 Mbit/s
LK1/2 Flashing Data transfer
green