Technical Specifications - AER Compact mobile Bedienungsanleitung

7. Technische Daten / Technical specifications
channel 1 High impedance, unbalanced instrument
or line input
Mono jack socket, ¼" (6.35 mm)
Min. input voltage:
Max. input voltage:
Input impedance:
Equivalent input noise voltage
(A-weighted):
High/low (attenuator) switch:
Phantom power: Optional (see notes),
9 V DC / max. 100 mA, on ring of input jack,
short circuit protected channel 1
clip indicator
Headroom:
channel 2 Switchable line / microphone input
Combo socket, XLR + jack ¼" (6.35 mm)
line mode (via jack input only)
High impedance, unbalanced
instrument orline input
Min. input voltage:
Max. input voltage:
Input impedance:
Equivalent input noise
voltage (A-weighted):
mic mode
Microphone input, XLR (balanced), stereo
jack (balanced), or mono jack (unbalanced)
1 / sleeve = ground,
2 / tip = positive (+),
3 / ring = negative (–)
Min. input voltage:
with low-gain option:
Max. input voltage:
with low-gain option:
(see notes)
Input impedance (balanced):
Input impedance (unbalanced):
Voice filter: –10 dB at 270 Hz referred to 10 kHz
Equivalent input noise voltage (
A-weighted):
Phantom power:
R = 6.8 kΩ per terminal, max. 10 mA total,
short-circuit protected
clip indicator
Headroom:
aux in Auxiliary stereo input, e.g. for CD player
Cinch (RCA) sockets, L / R
Level adjustable by aux level
Min. input voltage:
Max. input voltage:
Input impedance:
return Input from external parallel effect loop, or
supplementary input
Mono jack, ¼" (6.35 mm)
Min. input voltage: 320 mV (–10 dBV)
Max. input voltage: 5 V (+14 dBV)
Input impedance: 20 kΩ
(but 5 kΩ while external effect is switched
OFF by footswitch)
18
22 mV (–33 dBV)
5 V (+14 dBV)
2.2 MΩ || 350 pF
1.5 μV (– 117 dBV)
–10 dB
min. 6 dB
27 mV (–31 dBV)
7 V (+17 dBV)
2.2 MΩ || 350 pF
2.4 μV (– 113 dBV)
3.3 mV (–50 dBV)
5.8 mV (–45 dBV)
1 V (0 dBV)
1.8 V (+5 dBV)
1.2 kΩ
2.7 kΩ
0.9 μV (–121 dBV)
XLR only, 48 V, switchable,
min. 6 dB
100 mV (–20 dBV)
3.5 V (+11 dBV)
22 kΩ
line out Line output after master,
with aux in and effects
Mono jack, ¼" (6.35 mm)
Output voltage:
Output impedance:
Min. load impedance:
Residual noise (A-weighted): 4.5 μV (–107 dBV)
headphones Headphones output
Stereo jack socket, ¼" (6.35 mm),
L/R connected
When plugged in, internal speaker is muted.
Output power at rated
conditions:
Max. output power:
Output impedance:
Min. load impedance:
Note: Suitable for stereo headphones with
stereo jack only. Not functional with mono
jacks.
send Output for external parallel effect loop,
before master, after tone controls
Mono jack, ¼" (6.35 mm)
Output voltage
(efx pan fully clockwise):
Output impedance:
Min. load impedance:
tuner
Tuner output, after tone controls,
before'effects and master
Mono jack, ¼" (6.35 mm)
Output voltage:
Output impedance:
Min. load impedance:
DI-out
Balanced, non-isolated XLR output,
after tone controls, without aux in and effects
1 = ground,
2 = positive (+),
3 = negative (–)
Output voltage (differential): 93 mV (–21 dBV)
Output impedance: 47 Ω, each terminal to gnd
Min. load impedance (differential):
footswitch
Connector for a dual footwitch
Stereo jack, ¼" (6.35 mm)
Tip = internal effect on/off
Ring = external effect on/off
Sleeve = common (ground)
Function:
tone controls
channel 1
colour –3 dB at 700 Hz
+10 dB at 8 kHz
bass ±8 dB at 100 Hz (shelf type)
middle ±6 dB at 800 Hz
channel 2 treble ±8 dB at 10 kHz (shelf type)
bass ±8 dB at 100 Hz (shelf type)
treble ±11 dB at 10 kHz (shelf type)
internal effects Digital effect processor
1 Reverb (short predelay)
2 Reverb (long predelay)
3 Delay (320ms, repetitive)
4 Chorus
external effects Parallel effect loop, see send and return
700 mV (–3 dBV)
100 Ω
2 kΩ
2 x 8 mW / 32 Ω
2 x 100 mW / 1000 Ω
470 Ω (common for L/R)
not limited
900 mV (–1 dBV)
47 Ω
2 kΩ
225 mV (–13 dBV)
47 Ω
2 kΩ
1 kΩ
Switch ON = effect OFF