Wolf Garten Power Edition 40 H Gebrauchsanweisung Seite 14

Operation
Allgemeines zum Betrieb
Operating times
Please check noise abatement regulations prevailing in your
country.
Starter cord assembly K L
1. Press red button (K, 1) and keep it depressed.
2. Lift and hold operator presence bail arm (K, 2).
3. Pull the starter rope slowly to the holding bracket.
4. Twist the cord through the holder (L).
Always remove the starter cord from the holder before
folding the mower handles.
Oil Fill M
Check oil level regulary before mowing!
To check, do not screw in the dipstick.
Fill crankcase with quality oil SAE 30 up to the marking „Full"
on dipstick.Capacity approx. 0,6 litre . Lift mower slightly on the
oil filter side whilst pouring oil slowly.
Filling with Petrol
Do not smoke - no naked flames!
Switch off engine.
Avoid spilling petrol when engine is warm.
Use „low-octane petrol" (do not use Super Plus).
Avoid petrol spillage.
Do not inhale vapour.
Use of height adjustment N
Only when mower is stationary and rotating blade
has come to complete standstill.
Place hand into handle bar and depress button (1). Lift or
lower chassis until it engages into required position (2).
If possible, mow when grass is dry in order to protect turf.
Do not set cutting position too low when mowing very tall or wet
grass. We recommend an average cutting height of 4,0 - 5,0 cm.
Start K L
• On a fl at surface, if possible not in high grass.
Cold start
1. Set hand throttle (K, 1) on start.
2. Raise and hold the safety bracket (K, 2). Pull starter grip
(L) and return it slowly by hand.
3. After starting, slowly move the hand throttle to "Operate".
Switching wheel drive on/off K
Wheel drive on:
Lift drive bar (3).
Wheel drive off:
Release drive bar (3).
Selecting the speed (Vario)
1. Press button (4)
2. Use the lever (5) to select the desired working speed
(2.5 km/h - 5.0 km/h).
Rabbit: faster. Snail: slower.
Tips for mowing O
• To prevent strips of grass from being left unmowed, the
cutting paths must always overlap a few centimeters.
• Always turn the mower on a surface that has already been
mowed.
14
All manuals and user guides at all-guides.com
Activating the cut/ collect function P
Hanging the grass bag Q
Emptying the grass bag R
Activating the mulch function P
Mowing
Make sure the motor is switched off and the
cutting blade is not moving.
• Turn the switch to „CUT/COLLECT".
Only when mower is stationary and rotating blade
has come to complete standstill.
1. Lift the protective fl ap.
2. Hang the grass bag in the chassis with the hooks in the
recesses (see arrow).
3. Replace the protective fl ap
Only when mower is stationary and rotating blade
has come to complete standstill.
• When the grass bag is full, the fl ap lowers automatically.
• To ensure proper functioning: clean the holes beneath
the level indicator in the grass bag regularly with a hand
brush.
Mulching
„Mulching" is a process in which the grass is fi nely chop-
ped by a special cutting system and then deposited on the
ground. The result is that the grass does not have to be
collected and disposed of. „Mulching" also prevents the lawn
from drying out.
Note:
• Depending on how fast the grass grows, you should mulch
1-2 times each week.
• The grass should not be too high or very wet!
• Walk slowly.
• When cutting, the strips should overlap.
• Do not cut more than 20 cm of grass at a time.
Important!
„Mulching" is not recommended if the lawn is mossy or
matted.
Reason:
The cut grass remains on top fo the moss or matted grass
and cannot reach the ground below.
Remedy:
The lawn should be aerated and fertilized regularly.
Only when the motor is switched off and the
cutting blade is not moving.
1. Remove the grass collecting bag.
2. Set the switch to „MULCH".