General Power Tool Safety Warnings - Makita CS002G Betriebsanleitung

SAFETY W ARNINGS

General power tool safety warnings

WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
( c o r d l e s s ) p o w e r t o o l .
Cordless Metal Cutter safety
warnings
Cutting procedures
1. DANGER: Keep hands away from cutting
area and the blade. Keep your second hand
on auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by
the blade.
2. Do not reach underneath the workpiece. T h e
guard cannot protect you from the blade below the
w o r k p i e c e .
3 . Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
4 . Never hold the workpiece in your hands or
across your leg while cutting. Secure the
workpiece to a stable platform. I t i s i m p o r t a n t t o
support the work properly to minimise body expo-
sure, blade binding, or loss of control.
5. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting tool may contact hidden wiring.
C o n t a c t w i t h a " l i v e " w i r e w i l l a l s o m a k e e x p o s e d
m e t a l p a r t s o f t h e p o w e r t o o l " l i v e " a n d c o u l d g i v e
t h e o p e r a t o r a n e l e c t r i c s h o c k .
W hen ripping, always use a rip fence or
6.
straight edge guide. This improves the accuracy
of cut and reduces the chance of blade binding.
Always use blades with correct size and shape
7 .
(diamond versus round) of arbour holes. B l a d e s
t h a t d o n o t m a t c h t h e m o u n t i n g h a r d w a r e o f t h e
saw will run off-centre, causing loss of control.
8. Never use damaged or incorrect blade wash-
ers or bolt. The blade washers and bolt were
specially designed for your saw, for optimum
performance and safety of operation.
Kickback causes and related warnings
— kickback is a sudden reaction to a pinched,
jammed or misaligned saw blade, causing an
u n c o n t r o l l e d s a w t o l i f t u p a n d o u t o f t h e w o r k p i e c e
t o w a r d t h e o p e r a t o r ;
— when the blade is pinched or jammed tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
o p e r a t o r ;
— if the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can
d i g i n t o t h e t o p s u r f a c e o f t h e w o r k p i e c e c a u s i n g
the blade to climb out of the kerf and jump back
t o w a r d t h e o p e r a t o r .
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
1. Maintain a firm grip with both hands on the
saw and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but
kickback forces can be controlled by the operator,
i f p r o p e r p r e c a u t i o n s a r e t a k e n .
W hen blade is binding, or when interrupting a
2.
cut for any reason, release the trigger and hold
the saw motionless in the material until the
blade comes to a complete stop. Never attempt
to remove the saw from the work or pull the
saw backward while the blade is in motion
or kickback may occur. I n v e s t i g a t e a n d t a k e
corrective actions to eliminate the cause of blade
binding.
3 . W hen restarting a saw in the workpiece, centre
the saw blade in the kerf so that the saw teeth
are not engaged into the material. If a saw blade
binds, it may walk up or kickback from the work-
p i e c e a s t h e s a w i s r e s t a r t e d .
Support large panels to minimise the risk of
4 .
blade pinching and kickback. L a r g e p a n e l s t e n d
to sag under their own weight. Supports must be
placed under the panel on both sides, near the line
o f c u t a n d n e a r t h e e d g e o f t h e p a n e l .
5. Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
6. Blade depth and bevel adjusting locking levers
must be tight and secure before making the
cut. If blade adjustment shifts while cutting, it may
cause binding and kickback.
7 . Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
8. ALWAYS hold the tool firmly with both hands.
NEVER place your hand, leg or any part of your
body under the tool base or behind the saw,
especially when making cross-cuts. If kickback
occurs, the saw could easily jump backwards over
your hand, leading to serious personal injury.
Never force the saw. Push the saw forward at a
9.
speed so that the blade cuts without slowing.
Forcing the saw can cause uneven cuts, loss of
accuracy, and possible kickback.
Lower guard function
1. Check the lower guard for proper closing
before each use. Do not operate the saw if the
lower guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If the saw is accidentally
dropped, the lower guard may be bent. Raise the
l o w e r g u a r d w i t h t h e r e t r a c t i n g h a n d l e a n d m a k e
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
7 ENGLISH