Residual Risk - Ryobi RHT36B60R Übersetzung Der Originalanleitung

■
Your hedge trimmer is equipped with two cutting
speeds:
●
Setting 1 (hi-speed) - Use this setting as the primary
mode of your hedge trimmer. At hi-speed setting,
the blade cuts at top speed, which allows quick and
precise trimming. This speed is best for the regular
maintenance of your hedges.
●
Setting 2 ( hi-torque) - Use this setting to cut thick or
dense hedges. The hi-torque setting provides more
cutting power to trim larger branches. This setting is
not intended for everyday trimming.
Use the speed switch to change the cutting speed
to your desired setting. You should not change the
cutting speed while the product is running.
WARNING
If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTATION AND STORAGE
■
Stop the product, remove the battery, and allow both to
cool before storing or transporting
■
Clean all foreign material from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. For extra safety, store the battery separately
from the hedge trimmer. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
■
Cover the blade with the blade protector before storing
the product, or during transportation.
■
For transportation, secure
movement or falling to prevent injury to persons or
damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
MAINTENANCE
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service we suggest you return the
product to your nearest authorised service centre for
repair. When servicing, use only identical replacement
parts.
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating and fitting or removing the blade protector.
■
■
■
■
■
■
the product against

RESIDUAL RISK

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
WARNING
WARNING
WARNING
Remove the battery before adjusting, maintaining, or
cleaning the product.
You may make adjustments and repairs described in
the manual. For other repairs, contact the authorised
service agent.
After each use, clean the body and handles of the
product with a soft, dry cloth.
After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade protector. The
manufacturer recommends you to use a rust preventative
and lubricant spray to apply an even distribution and
reduce the risk of personal injury from contact with the
blades. For information about suitable spray product
check with your local authorised service centre.
You may wish to lubricate the blades lightly before use
if necessary using the above method.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
The blades cannot be guarded whilst cutting. Contact
with the blades can cause serious injury. Keep the
blade away from yourself and others. Cover it with the
blade protector whenever you are not cutting.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English | 3