Functional Description - Makita UB100D Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before adjusting or checking function on the
machine.
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Hold the machine and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the machine and the
battery cartridge firmly may cause them to slip off
your hands and result in damage to the machine and
battery cartridge and a personal injury.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
► Fig.7: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the
machine while sliding the button on the front of the
cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Battery protection system
The machine is equipped with a battery protection
system. This system automatically cuts off power to the
motor to extend battery life.
The machine will automatically stop during operation if
the machine and/or battery are placed under one of the
following conditions:
Overloaded:
The machine is operated in a manner that causes it to
draw an abnormally high current.
In this situation, turn the machine off and stop the appli-
cation that caused the machine to become overloaded.
Then turn the machine on to restart.
If the machine does not start, the battery is overheated.
In this situation, let the battery cool before turning the
machine on again.
Low battery voltage:
The remaining battery capacity is too low and the
machine will not operate. If you turn the machine on,
the motor runs again but stops soon. In this situation,
remove and recharge the battery.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.8: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
WARNING:
tridge into the machine, always check to see that
the switch trigger actuates properly and returns
to the "OFF" position when released.
► Fig.9: 1. Switch trigger
To start the machine, pull the switch trigger. The speed
is increased by increasing pressure on the switch trig-
ger. Release the switch trigger to stop.
NOTICE:
If the machine has been operated con-
tinuously until the battery has become empty, rest
the machine for at least 15 minutes before operat-
ing the machine with a fresh battery.
Speed adjusting dial
► Fig.10: 1. Speed adjusting dial
The speed can be changed by turning the speed adjust-
ing dial to a given number setting from 1 to 3. Higher
speed is obtained when the dial is turned in the direc-
tion of number 3. Lower speed is obtained when it is
turned in the direction of number 1.
Refer to the table for the relationship between the num-
ber settings on the dial and the speed.
Number
3
2
1
NOTICE:
When turning the dial, be sure to com-
pletely release the switch trigger. Otherwise, the
machine may be damaged.
10 ENGLISH
Off
75% to 100%
50% to 75%
25% to 50%
Before installing the battery car-
Speed
High
Medium
Low
Remaining
capacity
0% to 25%