Assembly And Adjustments - DeWalt DWE575 Originalanweisungen

EN GLI SH
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
2
conductor size is 1.5 mm ; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. An
accidental start-up can cause injury.
Changing Blades
TO INSTALL THE BLADE (FIG. 2–5)
1. Using the lower guard lever (l), retract the lower
blade guard (j) and place blade on saw spindle
against the inner clamp washer (n), making
sure that the blade will rotate in the proper
direction (the direction of the rotation arrow
on the saw blade and the teeth must point in
the same direction as the direction of rotation
arrow on the saw). Do not assume that the
printing on the blade will always be facing you
when properly installed. When retracting the
lower blade guard to install the blade, check
the condition and operation of the lower blade
guard to assure that it is working properly. Make
sure it moves freely and does not touch the
blade or any other part, in all angles and depths
of cut.
2. Place outer clamp washer (o) on saw spindle
with the beveled edge facing out. Make sure the
30 mm diameter on the blade side of the clamp
fits into the 30 mm hole in the saw blade to
ensure centering of the blade.
3. Thread the blade clamping screw (k) onto the
saw spindle by hand (screw has right-hand
threads and must be turned clockwise to
tighten).
46
4. Depress the blade lock (d) while turning the
saw spindle with the blade wrench (p) stored
underneath the main handle (c) (fig. 5), until
the blade lock engages and the blade stops
rotating.
5. Tighten the blade clamping screw firmly with the
blade wrench.
NOTICE: Never engage the blade lock
while saw is running, or engage in an
effort to stop the tool. Never turn the
saw on while the blade lock is engaged.
Serious damage to your saw will result.
TO REPLACE THE BLADE (FIG. 2–5)
1. To loosen the blade clamping screw (k), depress
the blade lock (d) and turn the saw spindle with
the blade wrench (p), stored underneath the
main handle (c), until the blade lock engages
and the blade stops rotating. With the blade
lock engaged, turn the blade clamping screw
counterclockwise with the blade wrench (screw
has right-hand threads and must be turned
counterclockwise to loosen).
2. Remove the blade clamping screw (k) and outer
clamp washer (o). Remove old blade.
3. Clean any sawdust that may have accumulated
in the guard or clamp washer area and check
the condition and operation of the lower blade
guard as previously outlined. Do not lubricate
this area.
4. Select the proper blade for the application
(refer to Blades). Always use blades that are
the correct size (diameter) with the proper size
and shape center hole for mounting on the
saw spindle. Always assure that the maximum
recommended speed (rpm) on the saw blade
meets or exceeds the speed (rpm) of the saw.
5. Follow steps 1 through 5 under To Install the
Blade, making sure that the blade will rotate in
the proper direction.
LOWER BLADE GUARD
WARNING: The lower blade guard is
a safety feature that reduces the risk
of serious personal injury. Never use
the saw if the lower guard is missing,
damaged, misassembled or not working
properly. Do not rely on the lower
blade guard to protect you under all
circumstances. Your safety depends on
following all warnings and precautions
as well as proper operation of the
saw. Check the lower blade guard for
proper closing before each use. If the
lower blade guard is missing or not
working properly, have the saw serviced