Before Starting The Equipment; Attachment And Operation - Scheppach MFH380-20Li Dual Original Anleitungen

• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this
sign: m
7.

Before starting the equipment

Caution! Do not fi t the battery until the equipment
has been fully assembled and all the settings have
been actuated. Always wear protective gloves when
working on the equipment to protect yourself against
injury.
Each time before use, check the following:
• That the equipment is in perfect condition and that
the safety devices and cutting devices are com-
plete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
8.

Attachment and operation

ASSEMBLY
When assembling this machine, please follow the in-
structions for assembly printed.
Assemble the handle on the machine. Fig. 2-3
1
• Install the front handle as shown on the image 2.
• Make sure that you align the pin with the hole.
Tighten the screws only loosely before you have the
most comfortable working position set to the risers.
The front handle should be aligned as in pictures
2+3 shown, then tighten the screws.
2. Mounting the shaft. Fig. 4
• Open the handle (a)
• Push the shaft into the holder. Make sure that the
metal ball (b) is alignment with the hole (c) and
furthermore locks.
• After this process please fix the shaft by turning
the handle (a).
3. Assemble the safe guard. Fig. 5-7
• Fix the safe guard with hex key and wrench en-
closed as stardard accessories for tighting the nuts
enough. Please see the below pictures showing.
m Warning! Never use the machine without the
guard assembled!
4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 8-9
• Release the nut.
Line up the two holes of flange and shield, use
one screw driver to hold the flange as below and
turn the socket wrench clockwise, the nut will be
released.
• Fit the Nylon cutting head.
34 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Remove another shield after release the nut. Still
hold the flange, take the Nylon cutting head on the
shaft and rotate counter-clockwise, the Nylon cutting
head is fitted. Fig. 19
• Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 10-12
Take the outer flange off after release the nut, then
put the blade (17), outer flange (17b), shield (17a)
and nut according to priority as below picture. Note
the blade rotation direction needs be same as be-
low picture.
Use screw driver to hold flange and tighten nut
counter-clockwise, ensure the nut is tightened
enough.
• Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
m Warning!
Please make sure the cutting head has been assem-
bled correctly before use!
OPERATION
When working with the equipment as grass trimmer and
brush cutter, the appropriate plastic guard hood for cut-
ting blade mode or cutting line mode must be fi tted
to prevent objects being thrown out by the equipment.
The integrated blade (A) in the cutting line guard hood
automatically cuts the line to the optimum length. Fig.
17
5. Fit the belt. Fig. 13-16
• The Combined grass trimmer, pole saw, brush cut-
ter must be used with the strap.
• Balance the machine when the tool is switched off.
• Wear the shoulder strap.
• Adjust the strap length so that the snap hook (k) is
about a hand's breadth below the right hip. Hang
the multi-function tool on the karabiner
• Hang the brush cutter on a hook.
• Hang the machine.
• When standing in a normal working posture, the
blade should touch the ground during normal work-
ing position.
• Thereby, it is important that the
is always well balanced.
• For operation, hook the brush cutter into the snap
hook (k) of the carrying strap while the engine is
running.
• ATTENTION! In an emergency, the safety latch (l)
can be pulled from the harness. The machine then
detaches immediately from the carrying strap (9)
and falls to the ground.
6. Mounting the hedge trimmer Fig. 27-29
• Remove the screw (d), align the holes (c) so that they
are flush and screw the screw (d) back in.
petrol brush cutter