Automatic Restart - Husqvarna LC 247i Bedienungsanweisung

LED display
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To start the product (LC 247i)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 30)
4. Stay behind the product.
5. Loosen the start inhibitor. (Fig. 17)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 31)
To start the product (LC 347iVX,
LC 353iVX)
1. Open the battery lid.
2. Put a charged battery in 1 of the battery holders. For
longer operation time, put a second charged battery
in the other battery holder.
3. Turn the safety key to 1. (Fig. 32)
4. Stay behind the product.
5. Push the ON/OFF button (A) on the control panel.
The display comes on. The battery indicator (B)
shows the battery charge of the 2 batteries. The
number of the battery that operates is shown
adjacent to the battery indicator. For models
LC 347iVX, LC 353iVX, the display also shows the
set speed. (Fig. 33)
6. Loosen the start inhibitor. (Fig. 34)
7. Push the motor brake handle in the direction of the
handlebar. (Fig. 35)
To use the drive on the wheels
LC 347iVX, LC 353iVX
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 36)
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 37)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE
The product has a battery saving function (SavE
gives longer operation time.
16
Charging status
50%-75%
75%-100%
Fully charged
™
function (LC 247i)
• Push the SavE
function. (Fig. 38)
• Push the SavE
function.
Note:
The SavE
ground conditions make it necessary to have a higher
output. The SavE
when the ground conditions let it.
To use the SavE
(LC 347iVX, LC 353iVX)
The product has a battery saving function (SavE
gives longer operation time.
1. Push the SavE
™
SavE
2. Push the SavE
The SavE
39)
Note:
The SavE
ground conditions make it necessary to have a higher
output. The SavE
when the ground conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.

Automatic restart

During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product tries to
restart automatically. If the product does not restart in 5
seconds, it can be necessary to clean below the cutting
cover. Refer to
To stop the product (LC 247i)
1. Release the motor brake handle to stop the motor.
™
) that
(Fig. 40)
2. Open the battery lid and turn the safety key to 0.
(Fig. 41)
™
button to position 1 to start the
™
button to position 0 to stop the
™
function stops automatically if the
™
function starts automatically again
™
function
™
button (A) to start the function. The
symbol (B) on the display comes on.
™
button again to stop the function.
™
symbol (B) on the display goes out. (Fig.
™
function stops automatically if the
™
function starts automatically again
To clean the product on page 18 .
WARNING:
Before a check of the
cutting cover, release the motor brake
handle, turn the safety key to 0, remove the
battery and wait at minimum 5 seconds.
There is a risk of injury if the obstacle is
removed and the product accidentally starts.
WARNING:
Turn the safety key to 0
before you let the product out of view.
1696 - 002 - 03.12.2021
™
) that