Herunterladen Diese Seite drucken

Chicco Next 2 Me Magic Bedienungsanleitung Seite 16

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 22
the bed). If this is not the case, use the adjustment system to
achieve this condition on both sides.
WARNING: In side sleeping configuration, the 2 leg supports
of the crib must be set at the same height.
3. To fasten the crib to the parents' bed (side sleeping
configuration), use the pair of supplied straps "F".
4. Carefully release the buckles "D6" and "D7" by pushing them
slightly upwards and then pulling them out (Fig.24).
5. Fasten the grey buckles "F2" to the buckles "D6" located in the
rear part of the bottom of the crib "D4" (Fig.25).
6. Fasten the red buckles "F1" to the buckles "D7" located in the
front part of the bottom of the crib "D4" (Fig.26).
7. Then pass the straps around the parents' bed structure from
top to bottom (Fig.27) and fasten the grey buckles "F3" to
form a loop (Fig.28). Make sure to repeat the step on both
sides. To make installation easy, when fastening the buckles,
always keep the crib slightly away from the parents' bed.
8. At this point put the crib against the parents' bed and tighten
the noose pulling the straps (Fig.29). Carry out this step first
on one side and then on the other, adjusting the straps until
the crib is in contact with the parents' mattress.
WARNING: Before use, always make sure that there is no space
between the parents' mattress and crib's side. Otherwise adjust
the straps pulling them until the required condition is restored.
Make sure that the side is always free to be lowered and raised
completely.
9. Lock the crib's wheels.
If when fastening the crib to the parents' bed it is not possible
to fit the crib's feet under the parents' bed, the crib can be
fastened anyway by the following the instructions above and
retracting the telescopic feet "A5" when putting the crib against
the bed.
To activate retraction, simply push the crib towards the bed so
that the release buttons "A4" (Fig.30) are activated, retracting
the feet as much as necessary to install the crib correctly.
10. To close the side, simply lift it upwards, holding it from the
centre (Fig.31). Always make sure that it is engaged correctly.
WARNING: Whenever the side is lowered, make sure that the
position compared to the parents' mattress has not changed
from that illustrated in the paragraphs above.
WARNING: Never use the rocking function when the crib is in
"Side sleeping configuration (fastened to the bed). "
WARNING: Use the product with beds and/or mattresses with
straight sides only. Do not use the product with round beds
and/or mattresses or water mattresses.
WARNING: When the product is used in "Side sleeping
configuration (fastened to the bed), " it must always be mounted
on the long side of the bed. DO NOT install the product at the
head or feet of the bed.
CARE AND MAINTENANCE
The crib and mattress have a resistant fabric lining that can be
removed completely and washed.
To remove the fabric, follow the instructions in the paragraph
"HOW TO REMOVE THE FABRIC COVER. "
WARNING: Covering or removing the fabric may take a few
minutes and must be carried out by an adult.
Regularly inspect the crib for signs of wear and any damage.
In the case of damage do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the
instructions on the label.
Do not use solvents, abrasive or overly aggressive products.
Hand wash in cold water
Do not bleach
All manuals and user guides at all-guides.com
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition
after each wash.
WARNING: When covering or removing the cover, take care
when handling the fabric parts so as to avoid accidental tears
or damage.
WARNING: The fabric part of drop side cannot be removed.
Do not open the zipper.
MAKING THE BED
It is possible to unfasten the crib from the parents' bed when
making the bed. Just unfasten the grey buckles under the fabric
lining.
When fastening the crib again to the parents' bed, pull the
straps again to make sure that the crib is correctly and securely
fastened to the parents' bed. Make sure that all the steps
illustrated above in "Side sleeping configuration (fastened to
the bed)" have been completed.
REMOVING THE COVER
1. Remove the mattress.
2. Release the crib structure "D" from the feet "A" by pushing the
buttons "A9.1" and pulling it upwards (Fig.32).
3. Open the 3 zippers "D1.1" and "D1.2" on the fabric.
4. Release the fastening buttons "D1.3. "
5. Remove the side support uprights "E" by pushing on the
appropriate tabs (Fig.33) and operating on the pins in the
upper fasteners to remove them from the fabric.
6. You can now remove the lining.
DISASSEMBLING THE CRIB
The crib can be disassembled completely to put it away in the
supplied bag. In order to complete the disassembly of the crib
after removing the fabric, remove the bottom bar "B" and the
central support structure "C" by repeating the steps illustrated
in "ASSEMBLY OF THE CRIB. "
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as provided for by the instructions.
The warranty shall not therefore apply in the case of damage
caused by improper use, wear or accidental events. For the
duration of the warranty on conformity defects please refer
to the specific provisions of applicable national laws in the
country of purchase, where appropriate.
16

Werbung

loading