Husqvarna LB 548i Bedienungsanweisung Seite 22

• Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.
Husqvarna Fleet Services
Husqvarna Fleet Services
the commercial fleet manager an overview of all
products. It is a requirement to have the Husqvarna
™
Fleet Services sensor installed on the product. The
product is prepared for installation of a Husqvarna Fleet
™
Services sensor. For more information about
Husqvarna Fleet Services
www.husqvarna.com.
To prepare the sensor (accessory)
1. Use the sensor key to open the lid of the sensor.
(Fig. 40)
2. Remove the sensor.
3. Connect the battery to the sensor. The LED light of
the sensor comes on. (Fig. 41)
4. Download the Husqvarna Fleet Services
5. Log on to the Husqvarna Fleet Services
6. Do a pairing operation. Refer to
operation between the app and the product on page
22
To do a pairing operation between the app
and the product
1. Log on to the Husqvarna Fleet Services
2. Select your product in the app.
3. Scan the code behind the sensor with your mobile
device to install the sensor in the app.
Note:
It is only necessary to do a pairing operation
between the app and the product one time.
To install the sensor
1. Make sure that the sensor is connected to the
Husqvarna Fleet Services
pairing operation between the app and the product
on page 22 .
2. Drill 2 holes by the marks in the enclosure slot. (Fig.
42)
Note:
Make sure that the holes are the same
dimension as the rivets supplied with the sensor.
3. Use a pair of pliers to remove the outer holes on the
sensor slot. (Fig. 43)
22
™
™
is a cloud solution that gives
™
, refer to
™
app.
™
app.
To do a pairing
™
app.
™ To do a
app. Refer to
4. Drill 2 holes by the marks in the sensor slot. (Fig. 44)
5. Align the sensor slot with the enclosure slot. (Fig. 45)
6. Attach the sensor slot with the rivets.
7. Install the sensor in the sensor slot. Align the white
mark on the sensor with the mark on the sensor slot.
(Fig. 46)
8. Close the lid to the sensor and lock it with the sensor
key. Make sure that the top of the Husqvarna "H"
points away from the safety key. (Fig. 47)
To set the product in operation position
(LC 551iV)
1. Lift the handle to upright position. (Fig. 48)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 33)
3. Tighten the knobs fully.
To set the cutting height (LB 548i,
LC 551iV)
The cutting height can be adjusted in 6 levels.
1. Push the cutting height control in the direction of the
wheel and then rearward to increase the cutting
height.
2. Push the cutting height control in the direction of the
wheel and then forward to decrease the cutting
height. (Fig. 49)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.
To set the cutting height (LB 553iV)
The cutting height can be adjusted in 5 levels.
1. Move the cutting height lever rearward to increase
the cutting height.
2. Move the cutting height lever forward to decrease
the cutting height. (Fig. 50)
CAUTION:
too low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING:
you must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
Do not set the cutting height
Do not set the cutting height
Before you use the battery,
1630 - 002 - 24.09.2021