Residual Risks; Maintenance - Ryobi RCD1802 Originalanleitung

Safety, performance, and dependability have been given
top priority in the design of your drill driver.
INTENDED USE
The drill driver is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions. The product can be used for drilling into various
materials, including wood, metal, and plastics using a drill
bit having a shank diameter of less than 13 mm.
The product can be used to drive and remove screws and
bolts using an appropriate bit.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL DRIVER SAFETY WARNINGS
■ Wear ear protectors when drilling. Exposure to noise
can cause hearing loss.
■ Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■ Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
■ Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
■ When not in use, all tools should be disconnected from
power source.
■ The dust produced when using the product may pose
a health hazard Do not inhale the dust. Wear a suitable
dust mask.
■ Do not operate on materials (e.g., asbestos) that
present a health hazard.
■ Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
it is tilted in the workpiece
–
it has pierced the workpiece
–
the product is overloaded
–
■ Sawdust and splinters must not be removed while the
product is running.
■ When working in walls, ceilings, or floors, avoid
electrical cables and gas or water pipes.
■ Secure your workpiece with a clamping device.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise, and the operator
should pay special attention to avoid the following:
■ Risk of electrocution if electric cables are drilled into.
Always grasp the product by designated handles; do
not touch the drill bits.
■ Injury caused by vibration. Hold the product by
designated handles and limit exposure to vibration. See
"RISK REDUCTION".
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.

MAINTENANCE

■ When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
UK
1