Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Cleaning and Special Maintenance
Filter Assembly
For best performance and
results, the filter assembly
must be cleaned frequently.
The filter efficiently removes
food particles from the wash
water, allowing it to be
recirculated during the cycle.
For this reason, it is a good
idea to remove the larger
food particles trapped in the
filter after each wash cycle
by rinsing the "A" semi-
circular filter and cup "C"under running water. To remove
the filter assembly, pull on the cup handle in the upward
direction. The entire filter assembly (made up of the "A"
semicircular filter and the "B" fine filter) should be cleaned
at least once a week.
To clean the filter and the fine filter, use a cleaning brush.
Troubleshooting
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
- Have you put the right amount of detergent into the
dispenser?
- Is the wash cycle suitable for the dishes you have placed
inside the appliance?
- Are the filter and microfilter clean?
- Can the sprayer arms turn freely?
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
C
A
B
Then, reassemble the
filter parts as shown in
the figures below and
reinsert the entire
assembly
in
the
dishwasher, positioning
in its seat and pressing
downward.
The dishwasher must
never be used without
the filters. Improper replacement of the filters may reduce
the performance level of the appliance and damage dishes
and utensils.
Cleaning the Sprayer Arms
It may happen that food particles become encrusted on the
sprayer arms and block the holes. Check the sprayer arms
periodically and clean them when needed (see "Close-up
View [interior]", letters F-I).
Error messages.
Your dishwasher is equipped with a safety system which is
able to detect any operating anomalies.
These anomalies are signalled by the rapid flashing of one or
more of the indicator lights "C".
If the indicator lights for the wash cycles 2 and 3 flash, cancel
the wash cycle by following the instructions indicated in the
"Modifying a wash cycle in progress" paragraph on page
36.
Now check whether there is any water in the mains supply
and that the tap is turned on; restart the wash cycle and if
the error message persists, then call for technical assistance,
indicating which message appeared.
If any other indicator lights apart from the above-mentioned
ones flash rapidly, turn the appliance off and call for technical
assistance, indicating which message appeared.
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
39
GB
Werbung
Inhaltsverzeichnis
