Machine Description; Recommended Use; Symbols And Signs - BATTIPAV E..GO 80 Bedienungsanleitung

GB
Maintain tools with care
• Keep tools sharp and clean for better and safer performance.
• Follow all maintenance advice and instructions to replace accessories subject to wear. Inspect tool cords periodically and, if
damaged, have them repaired by an authorised expert. Check extension cords periodically and replace them if damaged. Keep
handles dry, clean and free from oil and grease.
Disconnect tools
• When not in use, before servicing, and when changing accessories subject to wear.
Remove service keys from tool
• Form the habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
Avoid unintentional starting
• Be sure that the switch is off when plugging in the tool.
Extension cords for outdoor works
• When tool is used outdoors, use only extension cords intended for this particular use and so marked.
Stay alert
• Watch what you are doing. Use common sense. Do not operate tool when you are inattentive.
Check tool for damaged parts
• Before further use of the tool, check it and the safety devices for damages and be sure that they operate properly. Check for
functioning and binding of moving parts, breakage of parts, correct mounting, and any other conditions that may affect the
correct operation of the tool.
• Damaged safety devices or other parts should be properly repaired or replaced by an authorised Service Centre unless
otherwise indicated elsewhere in this instruction manual.
• Have defective switches replaced by an authorised Service Centre.
• Do not use tool if its switch cannot be turned on or off.
Warning
• For your personal safety use only accessories recommended in this instruction manual or in the relevant catalogues The use
of any other accessory or attachment other than those recommended in this instruction manual or in the relevant catalogue
may present a risk of personal injury.
Have tools repaired by qualified personnel
• This electric appliance is in accordance with the safety rules in force. Only qualified experts may carry out repairing of electric
appliances otherwise it may cause considerable danger for the user.
*
1
The noise level emitted by the machine was measured in accordance with the UNI EN12418, EN3744 standards. Measurements
were performed in the absence of load and at maximum speed using a cutting tool with a diameter of 350mm.
*
2
The machine in working conditions has a noise emission higher than 85 dB (A).
The vibration level transmitted to the hand-arm system was measured in accordance with the UNI EN ISO 5349-1 standard

MACHINE DESCRIPTION

The E.GO / EGO PLUS site cutter is a machine intended specifically for cutting ceramics, marble, granite, bricks, concrete items
and similar materials, up to a thickness of 125 mm.
The machine uses a wet diamond tipped tool cutting system and is intended for personnel specialized in the construction sector.
The operator works in front of the moving worktop, within reach of the operating controls, and positions the material to be cut on
the moving worktop. He/she moves the moving worktop forwards to bring the material into contact with the tool.

RECOMMENDED USE

CUTTING TOOL DIAMOND BLADE WET CUTTING
CONTINUOUS CROWN: ceramic, marble, stone, single-fired ceramic
LASER/SECTORS: cement, natural stones, granite, abrasive materials (With narrow slots, max 5 mm).
TURBO: cement, natural stones, granite, refractory
THE TOOL / MATERIAL TO BE CUT MATCHES ARE PURELY INDICATIVE. ALWAYS FOLLOW THE INTENDED USE INDICATIONS
PROVIDED BY THE CUTTING TOOL MANUFACTURER BEFORE ANY APPLICATION.
Admissible working conditions: INTERMITTENT - S6 SERVICE 40%

SYMBOLS AND SIGNS:

Danger/prohibition stickers are applied to the machine where necessary. Look at these prior to using the machine.
35
A1 Use of prescribed PPE obligatory (Safety eyewear and earmuffs)
A2 Read operating instructions before each use.
A3 Use of prescribed PPE obligatory ( Protective Gloves )
A4 Warning! Danger of accidental contact
38
40%
60%
Under load running
Repose
B1 Do not use discs for wood or metal
B2 Do not wash with water under pressure
C1 Recovery tank water level
Battipav srl