Pulse; Knomap App - Christopeit Sport AX 3000 Montage- Und Bedienungsanleitung

Remark:
1. During body fat test, it will display Err2 if hand pulse sensors get no-
input.
2. According to test result, 10 seconds have no operation or operation
arbitrarily key, will get into system recommendation to toughen pro-
gram.
TEST-Pulse Recovery:
It is a function to check the condition of pulse recovery that is scaled
from 1.0 to 6.0 while 1.0 means the best and 6.0 means the worst and
the increment is 0.1. In order to get rated correctly, users must test it
right after the workout finished by pressing „TEST" key and then stop
exercising. After the key is pressed, please also apply the heart rate de-
tector appropriately. The test will last for 1 minute and the result will
show in the display.

PULSE

1. Pulse Rate:
The whole set of heart rate detector include 2 sensors each side. Each
sensor has 2 pieces of metal parts. The correct way to get detected is
to gently hold both metal parts each hand. With the good signals pi-
cked up by the computer, the heart mark in the HEART RATE Display
shall flash. Sometimes the heart rate value is not useable, based on
wet hands or any other contact problems during exercising. If you need
high accuracy heart rate value you have to use an external heart rate
measurement with a pulse belt.
"WARNING" Heart rate monitoring system may be inaccurate. Over
exercise may result in injury or death. If you feel faint stop exercising
immediately.
WATT TABELLE
RPM and Power in Watt of Level 1 - Level 24 for AX 3000
Art.-Nr. 1907
LEVEL 20 RPM 30 RPM
WATT WATT
1
4 8
2 6 11
3 7 13
4 8 16
5 9 19
6
10 21
7 11 23
8 13 27
9 15 29
10 16 31
11 17 35
12 18 37
13 19 40
14
20 43
15 22 46
16 23 50
17 25 53
18 26 56
19
28 59
20 29 63
21 31 65
22 32 67
23 34 71
24 36 74
Remarks:
1.The power consumptions (Watt) are adjusted by measuring the dri-
ving speed (min-1) of axle and the braking torque (Nm).
2.Your equipment was tested to fulfill the requirements of its accuracy
classification before shipment, If you have doubts about the accuracy,
please contactwith your local retailer or send it to accredited test labo-
ratory to ensure or calibrate it.
(Please note that a deviation tolerance as noted on page 15, is permis-
sible.)
Error Messages
Each time the computer is restarted, it will run a quick test for functio-
nality. If something is not okay, it indicates possible errors:
E 1 This symbol and a warning tone appear if the wiring is incorrectly
connected or there is a fault in the resistance setting. Check all cable
connections, especially at the connectors. After eliminating the error,
press and hold the „Start / Stop" button for 2 seconds to reset the sys-
tem to 0.
21
40 RPM 5 0 R P M 60 RPM 70 RPM
WATT WATT WATT WATT
14 20 28 35
19 27 38 48
23 34 48 61
28 41 58 74
33 48 68 89
37 54 78 100
41 61 88 112
47 68 98 124
52 76 108 137
56 82 118 148
62 90 128 164
66 96 138 172
70 103 148 185
75 110 158 201
79 117 168 215
85 125 178 228
90 133 188 246
95 141 198 251
100 149 208 272
104 156 218 283
108 162 228 291
113 168 238 303
120 175 248 320
127 182 258 335
GB
80 RPM
WATT
42
60
77
93
110
125
142
159
176
187
203
220
236
252
269
286
304
318
332
346
361
378
397
416