Special Safety Instructions; Technical Data - Scheppach PL75 Originalbetriebsanleitung

the protective covering. Have the saw repaired before
use if the protective covering and spring do not work
perfectly. Damaged parts, sticky residuals or piles of
saw dust can interfere with the working of the lower
protective cover.
c) When making an "inserted cut" that does not descri-
be a right angle, make sure that the saw is guarded
against slipping to the side. Slippage can lead to a
saw blade jam and a kickback.
d) Do not put the saw on the workbench or the floor wit-
hout making sure that the protective cover is over the
saw blade. An unprotected, running saw blade can
move the saw against the cutting direction and saw
what is in the way. Check the delay time of the saw.
9. Additional safety instructions for all
sawing with a wedge
a) Use the right wedge for the saw blade that is in use.
The wedge must be thicker than the thickness of the
steel blade but thinner than the width of the teeth.
b) Adjust the wedge as described in the operating inst-
ructions. Incorrect thickness, position or direction can
be the reason that the wedge does not effectively pre-
vent a kickback.
c) Always use a wedge, except when making an inserted
cut. Reassemble the wedge after an inserted cut. The
wedge is in the way when making an inserted cut and
can cause a kickback.
d) In order for the wedge to be effective, it must be in the
sawing gap. For short cuts, a wedge does not work to
prevent kickbacks.
e) Never run the saw with a bent wedge. Even the smal-
lest defect can slow down the closing of the protec-
tive cover.
INSTRUCTIONS FOR ALL SAWS
• Do not use a sanding belt.
• Make sure that the wedge is adjusted so that the di-
stance to the sprocket ring of the saw blade is not
more than 5 mm and that the sprocket ring does not
stick out more than 5 mm above the lower edge of
the wedge.
• Make sure that the dust catching mechanism is cor-
rectly installed, as is described in this manual.
• Wear breathing protection.
• Only those saw blades recommended in the manual
should be used.
• Always wear ear protection.
• Replace the saw blades as described in this manual.
• The maximum cut depth is 75 mm.
If the electrical cable of this tool is damaged it must be
replaced by the manufacturer or the customer service
department or a similarly qualified specialist in order to
avoid dangers.
FURTHER SPECIAL SAFETY INSTRUCTIONS FOR
CIRCULAR SAWS
a) Only use the recommended saw blades which corre-
spond to EN 847-1.
b) Do not use sanding belts.
c) Only use the manufacturer's original saw.
Do not use any saw blades which do not correspond
to the characteristics described in these operating ins-
tructions. Saw blades may not be brought to a stop by
pressure on the machine from the side.
Make sure that the saw blade is tightly assembled and
turns in the correct direction.

10. Special Safety Instructions

Safety instructions for circular saws
- Hold the equipment on the insulated handles, when
you undertake work in which the tool being used could
come into contact with hidden electrical wires, or its
own cable. Contact with a live power source can elec-
trify the metal parts of the tool and lead to an electri-
cal shock.

11. Technical data

Dimensions
L x W x H mm
Saw blade ø mm / number of
teeth
Thickness of saw blade
Idling speed n
0
Mitre square
Depth of cut 90° mm
Depth of cut 45° mm
Weightkg
Motor V/Hz
Input W
Protection class
Sound pressure level
Sound power level
Typical weighted vibrations
Subject to technical modifications!
Warning: Noise can have adverse health effects. Should
the noise level increase above 85 dB(A), you must wear
ear protection. Should the electrical supply not be opti-
mal, then the current can drop for a short time when the
machine is turned on. This can influence other equip-
ment (for example, the blinking of a lamp). Should the
electrical capacity have a Zmax < 0.27, such disturban-
420x300x235
210 / 36
1,6
4500
0°-45°
75
55
6,9
230 / 50
1600
II
95 dB(A),
K : 3 dB (A)
pA
106 dB(A),
K : 3 dB (A)
wA
a 5,72 m/s
2
h:
K: 1,5 m/s
2
GB 17