Herunterladen Inhalt Inhalt Diese Seite drucken

Block Function - Küppersbusch KI6750.0SR Bedienungsanweisung Mit Montageanweisungen

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Each action is verified by a beep.
Use the cursor slider (2) to adjust
power levels (0 - 9) by sliding your
finger over it. Sliding towards the right
increases the value, whereas sliding
towards the left decreases it.
It's also possible to directly select a
power level by placing your finger
directly on a desired point of the cursor
slider (2)
In order to select a plate on
these models, directly touch the
cursor slider (2).
SWITCHING ON THE DEVICE
1 Touch the On touch key
least one second. The touch control
will become active, a beep will be
heard and the indicators (3) will light
up displaying a "-". If any cooking
area is hot, the related indicator will
flash an H.
If you do not take any action in the
next 10 seconds the touch control will
switch off automatically.
When the touch control is activated,
you can disconnect it at any time by
touching the touch button
if it has been locked (lock function
activated). The touch button
always has priority to disconnect the
touch control.
ACTIVATING PLATES
Once the Touch Control is activated
with sensor
(1), any plate can be
turned on by following these steps:
1 Slide the finger or touch in any
position of one of the cursors
"slider" (2). The zone has been
selected and simultaneuously the
power level will be set between 0
and 9. That power value will be
shown on the corresponding power
indicator and its decimal dot (4) will
keep light up during 10 seconds.
2 Use the cursor slider (2) to choose
a new cooking level between 0 and
9.
As long as the plate is selected, in
other words, with the decimal (4)
dot light up, its power level can be
modified.
TURNING OFF A PLATE
Using the touch slider key (2) lower
the power to level 0. The hotplate will
switch off.
When a hot plate is switched off an
H will appear in its power indicator
(1) for at
(3), if the glass surface of the related
cooking area is hot and there is a risk
of burns. When the temperature drops,
the indicator (3) switches off (if the hob
is disconnected), or otherwise a "-" will
light up if the hob is still connected.
TURNING ALL PLATES OFF
All plates can be simultaneously
disconnected by using the general on/
off sensor
(1). All plate indicators (3)
will turn off. If the heating zone turned
off is hot, its indicator shows an H..
(1), even
(1)
Pan detector
Make sure that the bottom of
the vessel, covers one or more of
the references (+) on the surface of
the hob; (see fig.3 and table 1).
Induction cooking zones have a built-in
pan detector. This way, the plate will
stop working if there is no pan present
or if the pan is not suitable.
The power indicator (3) will show a
symbol to designate "there is no pan
" if, while the zone is on, no pan is
detected or the pan is not suitable
Fig.2
If a pan is taken off the zone while it
is running, the plate will automatically
stop supplying energy and it will
show the symbol for "there is no pan".
When a pan is once again placed
on the cooking zone, energy supply
will resume at the same power level
previously selected.
The time for pan detection are 30
seconds. If a pan is not placed
within this time period, or the pan is
unsuitable, the cooking zone shuts off.
When finished, turn off the
cooking zone by using the touch
controls. Otherwise an undesired
operation could occur if a pan is
accidentally placed on the cooking
zone during the 30 seconds. Avoid
possible accidents!

Block Function

With the Block Function, you can block
the other sensors, except for the on/
off sensor
undesired operations. This function is
useful as a childproof safety.
To activate this function, touch sensor
(6) for at least one second. Once
you have done so, the pilot (7) turns
on indicating that the control panel is
blocked. To deactivate the function,
simply touch sensor
If the on/off sensor
to turn off the appliance while the
block function is activated, it won't be
possible to turn the cooktop on again
until it unblocks.
Silencer of the beep
When the hob is on, if one presses the
touch key
EN
(1), in order to avoid
(6) again.
(1) is used
(11) and the locking touch
39

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ki6750.0

Inhaltsverzeichnis