Attachment And Operation - Scheppach HBS300 Original Bedienungsanleitung

• Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such
as goggles. Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regu-
larely check saw band for such defects.
• Risk of injury for fingers and hands while changing
saw band. Wear proper gloves.
• Risk of injury due to starting saw band while
switching on the machine.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Wear only closefitting clothes. Remove rings,
bracelets and other jewelry.
• For the safety of long hair, wear a cap or hair net.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by follow-
ing the instructions in „General safety instructions"
„Proper Use" and in the entire operating manual.

8. Attachment and operation

Before starting the equipment
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base. There are two holes
for this purpose in the machine foot. • The saw table
must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
• Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Assembly tools
1 engineer's wrench SW 10/13
8.1 Mounting the base (Fig. 2+3)
Installation parts:
• 4 stand feet (A)
• stand braces below (B): 2 x long + 2 x short
• stand braces above (C): 2 x long + 2 x short
• 4 rubber feet (D), 4 washer 8, 4 nuts M8
• Mounting parts (24 carriage bolts M8x16, 4 hex
screws M8x45, 32 washer 8, 28 nuts M8)
Hand-tighten all screws lightly during the installation.
• Place the 4 rubber feet on the stand feet.
• Attach one stand brace below (B) each with 2
screws M8 x 16, 2 washer and 2 nuts to the stand
feet (A).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Mount the frame struts above (C), each with 4 car-
riage bolts M8 x 16, 4 washers and 4 nuts on the
frame feet (A) as shown in Fig. 3.
• Place a cardboard box behind the machine and
then carefully tip the machine backward until the
machine rests on its housing.
• Place the previously assembled frame (Fig. 2) un-
der the base plate (E) of the band saw; screw it into
place by hand with 4 hex bolts M8x45, 8 washers,
4 circlips and 4 hex nuts. (Fig. 3)
• Set the machine with the base on a level surface
and tighten all the screws and nuts firmly.
8.2 Assembling the work table, (Fig. 4-6)
• Lay the table insert (a) in the recess in the work
table intended for this (Fig. 4). (To replace, disas-
semble the work table in reverse order.)
• Place the band saw blade through the slot on the
machine table. Place the machine table on the ta-
ble guide so that the fixing screw (b) fits through
the bracket (c).
• Screw the machine table tight with the wing nut
(E).
• Check that the bandsaw blade runs freely and does
not touch the table.
• Using the adjustment screw (F) to adjust the table
to a right-angle.
– Use a set square –
• Counter the adjustment screw (F) and tighten the
wing nut (E).
• Set the scale pointer (G) to 0.
• Adjust the angle scale (I):
• By loosening the screws (H) and shifting the angle
scale (I) until the scale pointer (G) points to 0. Fix
screws.
8.3 Assembly of the length end stop (Fig. 7+8)
• Turn the four knurled screws (J), each with a
flat washer, roughly 5 mm into the table surface
(Fig. 7)
• Place the guidance tube so that it touches the table
and tighten the four knurled screws (J).
• Now, put the length end stop (5) on the guidance
pipe, to the left of the saw blade, and clamp it
tightly. The end stop pipe should now be parallel
to the table groove.
8.4 Setting the number of revolutions
(Fig. 10+11+11.1)
Pull the mains plug!
• Open lower guard.
• Release the belt with the tension handle (10).
• Put the belt into the desired position. (L1 or L2).
• Retension the belt with the tension handle (10).
• Close the lower guard.
Rpm range:
Rpm stage 1 360 m/min.
GB | 27