Makita RP1800 Bedienungsanleitung Seite 6

ENGLISH
1-1. Adjusting knob
1-2. Lock lever
1-3. Stopper pole setting nut
1-4. Fast-feed button
1-5. Adjusting bolt
1-6. Stopper block
1-7. Depth pointer
1-8. Stopper pole
2-1. Nylon nut
3-1. Stopper pole
3-2. Adjusting bolt
3-3. Stopper block
4-1. Lock button
4-2. Switch trigger
5-1. Speed adjusting dial
6-1. Lamp
7-1. Shaft lock
7-2. Wrench
9-1. Feed direction
9-2. Bit revolving direction
9-3. Workpiece
9-4. Straight guide
10-1. Straight guide
10-2. Fine adjusting screw
SPECIFICATIONS
Collet chuck capacity
Plunge capacity
No load speed (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Explanation of general view
10-3. Clamping screw (B)
10-4. Clamping screw (A)
10-5. Guide holder
12-1. More than 15 mm
12-2. Straight guide
12-3. Wood
15-1. Adjusting screw
16-1. Screws
16-2. Movable
17-1. When set to minimum opening
width
18-1. When set to maximum opening
width
20-1. Template guide
20-2. Lock plate
21-1. Bit
21-2. Base
21-3. Templet
21-4. Workpiece
21-5. Distance (X)
21-6. Outside diameter of the templet
guide
21-7. Templet guide
23-1. Guide holder
Model
-1
)
Overall length
Net weight
Safety class
RP1800/
RP1800F
22,000
6.0 kg
ENE010-1
For Model RP1800,RP1800F,RP1801
For European countries only
Noise
ENF002-1
The typical A-weighted noise level determined according
to EN60745-2-17:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Vibration
The vibration
determined according to EN60745-2-17:
Work mode : cuttig grooves in MDF
Vibration emission (a
6
23-2. Adjusting screw
23-3. Clamping screw (B)
23-4. Clamping screw (C)
23-5. Trimmer guide
23-6. Clamping screw (A)
24-1. Bit
24-2. Guide roller
24-3. Workpiece
26-1. Flat washer 6
26-2. Screw M6x135
27-1. Flat washer 6
27-2. Screw M6x135
28-1. Hole
29-1. Screw M6x135
29-2. Threaded part in the motor bracket
30-1. Inside of the screw hole in the tool
base
31-1. Threaded part in the motor bracket
32-1. Screwdriver
33-1. Limit mark
34-1. Brush holder cap
34-2. Screwdriver
RP1801/
RP2300FC
RP1801F
12 mm or 1/2"
0 - 70 mm
9,000 - 22,000
312 mm
/II
) : 86 dB(A)
pA
) : 97 dB(A)
WA
Wear ear protection
total value (tri-axial
2
) : 4.0 m/s
h
RP2301FC
6.1 kg
ENG102-1
ENG223-1
vector sum)