General Safety Instructions For Power Tools - REMS Nano Betriebsanleitung

g
Translation of the Original Instruction Manual
Fig. 1 – 2
1 Base frame
2 Pipe arm
3 Fastening holes (not illustrated)
4 Cutting wheel
5 Hexagonal nut

General Safety Instructions for Power Tools

WARNING
Read all the safety notes, instructions, illustrations and technical data which
Failure to heed the following instructions can lead to
electric shock, re and/or severe injuries.
Keep all safety notes and instructions for the future.
The term "power tool" in the warnings refers to your mains operated (with power
cable) power tool or battery-operated (without power cable) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
di ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
tool will increase the risk of electric shock.
increase the risk of electric shock.
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
electric shock.
3) Personal safety
ting a power tool. Do not use a power tool while you are tired or under the
operating power tools may result in serious personal injury.
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
tool. Carrying power tools with your nger on the switch or energising power
tools that have the switch on invites accidents.
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
hair can be caught in moving parts.
g) Do not take your safety for granted and ignore the safety rules for power
Careless handling can lead to severe injury within split seconds.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
storing power tools. Such preventive safety measures reduce the risk of star-
ting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
tool. Power tools are dangerous in the hands of untrained users.
accidents are caused by poorly maintained power tools.
6 Pipe rest
7 Handle
8 Safet inching switch
9 High-Power-Batter
Power tools create sparks
Unmo-
Water entering a power
Damaged or knotted cables
Use of an RCD reduces the risk of
A moment of inattention while
Protective
This enables
Loose clothes, jewellery or long
Many
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
Use of the power tool for operations different from those intended
could result in a hazardous situation.
Slippery handles and gripping surfaces prevent safe handling and control of the
power tool in unforeseeable situations.
5) Battery tool use and care
that is suitable for one type of battery pack may create a risk of re when used
with another battery pack.
other battery packs may create a risk of injury and re.
terminals together may cause burns or a re.
irritation or burns.
can behave unexpectedly and lead to res, explosions or injuries.
above 130°C (265°F) can cause an explosion.
g) Follow all the instructions for charging and never charge the battery or the
instructions. Incorrect charging or charging outside the permitted temperature
range can destroy the battery and increase the re risk.
6) Service
is maintained.
carried out by the manufacturer or authorised customer service points.
Safety instructions for electric pipe and Cordless
Pipe Cutting Machines
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
-
Save all warnings and instructions for future reference.
with a functioning PE conductor. There is a danger of electric shock.
cut with a reasonable feeding pressure. The power tool and the cutting wheel
are subject to heavier wear by too high feeding pressure and can be damaged.
A too high feeding pressure, the ends of the pipe to be cut are pressed further
inwards causing constriction of the cross section.
A
tool. This reduces off-centre running of the pipes and the cut pipes do not fall
onto the oor.
are not straight causes imbalance and the pipe or pipe rest can fall over. The
pipe can also slip off the material rest, the power tool can move and the cutting
wheel can be damaged. Danger of injury.
cutting. Danger of injury.
Only allow trained persons to use the power tool. Apprentices may only use
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
by a responsible person. Otherwise there is a risk of operating errors and
injuries.
Have these renewed by quali ed experts or an authorised
REMS customer service workshop in case of damage.
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
Shorting the battery
Liquid ejected from the battery may cause
Damaged or modi ed batteries
Fire or temperatures
This will ensure that the safety of the power tool
All maintenance of batteries should only be
There is a danger of accident.
There is a risk of injury.
Cutting pipes that
g
A charger
Use of any
-
-
7