Operation - Makita PDC01 Betriebsanleitung

2. Adjust the position of the waist belt. Pull up the
height adjustment lever, then adjust the position of the
waist belt by sliding the base plate, and then return the
lever.
► Fig.10: 1. Height adjustment lever 2. Base plate
3. Waist belt
NOTICE:
If the height adjustment lever is loose,
tighten the nut of the height adjustment lever.
When tightening the nut, do not tighten it excessively.
Otherwise, the height adjustment lever will not move.
► Fig.11: 1. Nut
3. Attach the adapter pocket to the waist belt with the
hook and loop fastener as shown in the figure.
► Fig.12: 1. Adapter pocket
NOTE: The adapter pocket can be attached on either
left or right side of the waist belt.
4.
Adjust the width of the shoulder harness using the
width adjustment belt.
► Fig.13: 1. Width adjustment belt
5. Wear the unit, then lock the buckle of the waist
belt, and then adjust the length of the waist belt.
► Fig.14: 1. Buckle
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.15: 1. Belt
6. Adjust the length of the shoulder harness.
► Fig.16: 1. Shoulder harness
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.17: 1. Belt

OPERATION

CAUTION:
When wearing the unit, be sure
to put shoulder harness on your both shoulders.
Otherwise, the unit may fall when you wear the unit or
use the unit, and cause an injury.
CAUTION:
When wearing the unit, be sure to
wear the unit on your back. Otherwise, the unit may
fall during operation and cause an injury.
CAUTION:
Always switch off the tool or
machine before turning on the unit, or connecting
the plug of the adapter or power tool/machine to
the socket of the battery box. Otherwise, the tool or
machine may start suddenly and cause an injury.
Connecting the unit to the tool or
machine
1. Pull out the cord from either left or right side of the
battery box. When pulling out the cord, be sure to set
the cord in the holders as shown in the figure.
► Fig.18: 1. Cord 2. Holder
2.
Wear the unit.
3.
Insert the plug of the adapter or power tool/
machine into the socket of the battery box all the way so
that the arrow mark on the plug is aligned with that on
the socket.
► Fig.19: 1. Plug 2. Socket 3. Arrow mark
NOTICE:
When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket. Otherwise, the cords may be damaged
and cause a malfunction of the unit.
NOTE: The plug and socket are disconnected if a
certain load is applied.
4. Install the adapters to the tool or machine in the
same way as the battery cartridge.
► Fig.20: 1. Adapter
NOTICE:
For 18 V battery-powered tool or
machine, use the adapter for 18 V. For 36 V (18 V x
2) battery-powered tool or machine, use the
adapters for 36 V (18 V x 2). For 36 V - 40 Vmax
battery-powered tool or machine, use the adapter
for 36 V - 40 Vmax.
For direct connection type tool or machine, no
adapter is required.
NOTICE:
When installing adapters to the tool or
machine, be sure to install the adapter equipped
with 2 cords to the location shown in the figure.
If you install the adapters incorrectly, the adapter
equipped with 2 cords cannot be inserted all the
way. In this case, do not insert the adapter forci-
bly. Otherwise, the tool or machine may be damaged.
► Fig.21: 1. Adapter with 2 cords
► Fig.22: 1. Adapter with 2 cords
NOTE: The direction of the cord of the adapter can be
changed in the range of approximately 180 degrees.
5. Press the power button to turn the power on. To
turn the power off, press the power button for a few
seconds.
► Fig.23: 1. Power button
14 ENGLISH