Storage; Electrical Connection - Scheppach 5902205901 Originalbetriebsanleitung

After approx. ten operating hours, lubrication of the
following parts is recommended:
• Bearing of the infeed and output roller
• Bearing of pulley and sprocket
The threaded spindle for height-adjustment of the
thicknessing table may only be treated with a dry lu-
bricant agent.
The table surfaces as well as the infeed and output
rollers must always be kept free from resin.
• Regularly clean infeed and output rollers.
• In order to avoid overheating of the motor, regular-
ly check the air openings for any dust sticking on.
• After a longer period of use, it is recommended to
have the machine checked by an authorized deal-
er service.
Tool care:
• Cutter block, clamping devices, knife supports
and knives must be regularly cleaned from res-
in, as a clean tool improves the planing quality.
To this purpose, clamping devices, knife supports
and knives can be put in a common resin remover
for 24 hours.
• Resin from aluminium tools may only be removed
with cleaning liquids not being aggressive to this
type of metal.
Attention:
In case of a bad condition of the electrical system,
the performance can drop for a short period of time.
Ask a specialist.

11. Storage

Wrap the power cord (29) around the cable holder
(30) provided for this purpose. For the sliding cane
the sliding cane holders (28) are provided.
Store the equipment and accessories out of chil-
dren's reach in a dark and dry place at above freez-
ing temperature. The ideal storage temperature is
between 5 and 30 °C.
Store the electric tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

12. Electrical Connection

m WARNING! Electric shock! There is a risk of
an injury caused by electric shock!
Defective cable or plug may cause electric shock.
Avoid body contact with earth parts to protect your-
self from electric shocks.
m Operation is only allowed with a safety switch
against stray current (RCD max. stray current of
30mA).
Insert the plug of the electrical cable in a socket of
suitable shape, voltage and frequency complying
with current regulations.
Do not pull the service cable to pull the plug out of
socket.
The electric motor is connected in a ready-to-op-
erate state. The connection corresponds to the
relevant VDE and DIN regulations.
The mains connection at the customer's work
place and the extension cable used must corre-
spond to these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that use of the product at any
freely selectable connection point is not allowed.
• Given unfavourable conditions in the power sup-
ply the product can cause the voltage to fluctuate
temporarily.
• The product is intended solely for use at connec-
tion points that
a) do not exceed a maximum permitted supply im-
pedance Z = 0,328 Ω , or
max
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consul-
tation with your electric power company if neces-
sary, that the connection point at which you wish to
operate the product meets one of the two require-
ments, a) or b), named above.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Faulty electrical connecting leads
Insulation damage often occurs at electrical connect-
ing leads.
Causes include:
• Pressure marks caused when connecting leads
are run through windows or the cracks of doors.
• Folds caused by the improper attachment of run-
ning of the connecting leads.
GB | 33