Updating Via Usb - Pioneer VSX-S520D Bedienungsanleitung

> Before Start > Part Names
System Setup
Input/Output Assign
Speaker
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via NET" if there
is nothing to update.
4. Press ENTER with "Update" selected to start update.
0 During the update, the TV screen may go black
depending on the updated program. In that case,
check the progress on the display of this unit. The TV
screen will remain black until the update is complete
and the power is turned on again.
0 "Completed!" is displayed when the update is
complete.
5. Press Í STANDBY/ON on this unit to turn the unit into
standby mode. The process is completed and your
firmware is updated to the latest version.
0 Do not use Í on the remote controller.
If an error message is displayed: When an error occurs,
"＊-＊＊ Error!" is displayed on the display of this unit. ("＊"
represents an alphanumeric character.) Check the
following:
0 -01, -10: Ethernet cable not found. Connect the
Ethernet cable properly.
0 -02, -03, -04, -05, -06, -11, -13, -14, -
16, -17, -18, -20, -21: Internet connection error.
Check the following:
– The router is turned on
– This unit and the router are connected via the network
Try to disconnect and then connect again the power to
the unit and router. This may solve the problem. If you
> Install
are still unable to connect to the Internet, the DNS server
or proxy server may be temporarily down. Check the
service status with your ISP provider.
0 Others: Disconnect then reconnect the AC power cord,
Hardware then repeat from the beginning.

Updating via USB

0 Prepare a 128 MB or larger USB storage device. FAT16
or FAT32 file system format.
– Media inserted in a USB card reader may not be used
for this function.
– USB storage devices with security function are not
supported.
– USB hubs and USB devices with hub function are not
supported. Do not connect these devices to the unit.
0 Delete any data stored on the USB storage device.
0 Turn off the controller component (PC etc.) connected to
the network.
0 Stop any playing Internet radio, USB storage device, or
server content.
0 When "System Setup" - "Hardware" - "HDMI" - "HDMI
CEC" in the Home is set to "On", set it to "Off".
0 Some USB storage devices may take long to load, may
not be loaded correctly, or may not be correctly fed
depending on the device or their content.
0 We will not be liable whatsoever for any loss or damage
of data, or storage failure arising from the use of the USB
storage device with this unit. Thank you for your
understanding.
0 The description may differ from the on-screen display but
that will not change the way to operate or the function.
1. Connect the USB storage device to your PC.
2. Download the firmware file from our company's website
to your PC and unzip.
Firmware files are named in the following way:
PIOSLM1001_S50000SASAFPSP_.zip
Unzip the file on your PC. The number of unzipped files
> Initial Setup > Playback
Supplementary information | Advanced Setup
and folders varies depending on the model.
3. Copy all unzipped files and folders to the root folder of
the USB storage device.
0 Make sure to copy the unzipped files.
4. Connect the USB storage device to the USB port of this
unit.
0 If you connect a USB hard disk drive to the USB port of
the unit, we recommend that you use its AC adapter to
power it.
0 If the USB storage device has been partitioned, each
section will be treated as an independent device.
5. Switch the input on the TV to that assigned to the unit.
6. Press on the remote controller.
7. Select "System Setup" - "Miscellaneous" - "Firmware
Update" - "Update via USB" with the cursors in order,
then press ENTER.
System Setup
Input/Output Assign
Speaker Hardware
0 If "Firmware Update" is grayed out and cannot be
selected, wait for a while until it starts up.
0 You will not be able to select "Update via USB" if there
is nothing to update.
| Others
E
N
63